This MKS Instruments 247 Four Channel Power Supply / Readout is used and in excellent condition.
247 Configuration: • Display Type: 3 ½ digit 0.56" Red LED, Display is 1 of 4 Sequentially Selectable • Number of Channels: 4 • Signal Inputs from MFC/MFM: 4 x 0-5 VDC • Gas Correction Factor (Scaling): 0.1-4.0 (Rear Panel) • External Set Point: 0-5 VDC • External ON/OFF: TTL-Compatible • Signal Outputs Unscaled: 4 x 0-5 VDC = 0-100% of F.S. • Signal Outputs Scaled: 0-2 VDC (Max)
This Helmut-Fischer Fischerscope XDAL-FD EDXRF Spectrometer is used and in excellent condition.
Configuration: • FD: Fast Detector • Tube: Micro • Detector: PIN • Filters: 3 • Aperture: 4 • Probe Placing: XYZ • CPU: 1.8 Ghz P4, 1GB RAM, 20GB HDD, Windows XP, XDAL-FT Software v6.19 with Monitor, Keyboard and Mouse
Input Voltage: 120 VAC Only
Click here to view the photo of a wafer taken with the device's on-board camera by an Artisan Technology Group technician.
Parts and Accessories: • (1) FI-SIM WinFTM Super X720 (Security USB Dongle) • (3) WINFTM V6 CDs (Version: 6.13, 6.14, 6.19) • (1) Serial Cable for connecting device to computer • (1) Video Cable for camera
Click here to view a photo of the parts and accessories.
This Uthe 228-1 Negative Electric Flame-Off Torch Controller is used and in excellent condition. This 228-1 controller is configured for an S & K torch. S & K torch sold separately.
This Kevex 952-102 Omicron X-Ray Fluorescence Spectrometer is used and in excellent condition. This unit was decommissioned from a production facility. A very good effort was made to retain accessories. A 50W source is installed. This unit will need some additional accessories to become complete: keyboard, mouse, monitor, PC to Kevex connection cable, etc.
Included Accessories: PC, X-Ray Warning Lamp, Serial and Power Cabling, Safety Gloves and Piping
This Helmut-Fischer Fischerscope XDL-XYZp Spectrometer is used and in excellent condition. This is the XDL unit only, and does not include computer or software. This unit ships with the holding plate.
This Wyko Rough Surface Tester RST-Plus Optical Profilometer is used and in excellent condition. This unit includes: Microscope, Support Stage, Control Boxes, Vibration Isolation Table, Computer, Color Display, Video Monitor, Printer, Joystick, Mouse, and Keyboard.
Monitors Dimensions: 36" W x 59" H x 36" D (91.4cm W x 149.86cm H x 91.4cm D) Scope Dimensions: 32" W x 59" H x 36" D (81.28cm W x 149.86cm H x 91.4cm D)
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
This Metcal APR-5000 Array Package Rework System Base Unit is used and in excellent condition. This unit ships as photoed and with accessories explicitly listed. It does not include additional accessories nor does it include software. Contact manufacturer for pricing and availability for additional accessories and software.
This PACE TF-2000 BGA / CSP Rework System is used and in good condition. The PC, software, connection cables, cooling fan, or other attachements are not included. Please contact manufacturer for pricing and availability.
This West-Bond K-1400 4 Watt Ultrasonic Generator is used and in excellent condition.
K-1400 Configuration: • Output Power (Low Side): 0 to 2 W • Output Power (High Side): 0 to 5 W • Output Frequency: 62 to 66 KHz, automatically tracked • Short Setting Time Range: 1 ms to 100 ms • Long Setting Time Range: 20 ms to 1 sec. • Required Transducer Impedance: 20 ohms nominal
This Wyko Rough Surface Tester RST-Plus Rough Surface Tester Optical Profilometer is used and in excellent condition. This unit includes: Microscope, Support Stage, Control Boxes, Computer, Color Display, Illuminator Lamp, Mouse, and Keyboard.
Computer Configuration: Processor: Pentium 90 MHz Memory: 32 MB OS: Windows 95 Software Installed: Wyko Vision Plus v1.8
Filter Options: • None
Installed Objectives: • RX2.5 • RX10 • RX40
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
This KLA Tencor SFS-7600 Surfscan Patterned Wafer Inspection System is used and in good condition. We do not have the expertise to fully test this unit and have documented all the information gathered from it in this page. It is recommended that the purchaser of this system contact KLA-Tencor for installation, setup and maintenance. A very good effort was made to retain accessories. This item will be sold as/is without warranty and will be priced accordingly. However, if desired, this unit can be inspected on-site. Please contact Artisan Technology Group Sales to set this up.
The aligner operated on boot up and the internal fixture accepted a 200mm wafer. The aligner takes 100, 125, 150, and 200mm wafers however the internal fixture will only take 200mm wafers; wafer racks are sold separately. The system needs both a vacuum and air source to operate. The right side keyboard door hinge is broken and the keyboard is missing two keys however this does not affect its functionality. Service screen indicates that the laser will need to be replaced. You can view image of the keyboard and service screen shot using the links below.
Included Accessories: View Photo of Low Speed Endmill View Photo of High Speed Spindle and Renishaw MP15 View Photo of Machine Tool Coolant View Photo of Included Manuals
This Inficon / Sigma Instruments EIES-IV Guardian Thin Film Deposition Controller is used and in excellent condition. This version features a High-Voltage LED on the front panel.
This Inficon XTC Thin Film Thickness and Rate Monitor is used and in excellent condition. This unit comes with the 007-251 oscillator kit and extra BNC cables.
Configuration: • Thickness Display Range: 0 - 999.9 kÅ • Rate Display and Control Range: 0 - 999.9 Å/sec • Measurement and Control Update Period: 0.25 sec • Shutter Delay: ±5% of Rate Set Point • Power Requirements: 120 / 240 V (+5, -25%), 50 - 60 Hz, 50 VA • Operating Temperature: 0 - 50°C
This Wyko Rough Surface Tester RST-Plus Rough Surface Tester Optical Profilometer is used and in excellent condition. This unit includes: Microscope, Support Stage, Control Boxes, Vibration Isolation Table, Computer, Illuminator Lamp, Printer, Mouse, and Keyboard.
Computer Configuration: Processor: Pentium 166 MHz Memory: 32 MB OS: Windows 95 Software Installed: Wyko Vision Plus v1.8
This Kevex 952-102 Omicron X-Ray Fluorescence Spectrometer is used and in excellent condition. The unit also includes a monitor for viewing results. This unit was decommissioned from a production facility. A very good effort was made to retain accessories. A 50W source is installed. This unit will need some additional accessories to become complete: PC to Kevex connection cable, etc.
Included Accessories: PC, Mouse Keyboard, CRT Monitor (not shown in photos), Joystick (not shown in photos), X-Ray Warning Lamp, Serial and Power Cabling, Safety Mask and Piping
This Inficon XTC Thin Film Thickness and Rate Monitor is used and in excellent condition. This module is a combination of (2) Inficon XTC Controllers. These controllers can be sold separately if required. Please contact Artisan Technology Group sales for pricing and availability.
Configuration: • Thickness Display Range: 0 - 999.9 kÅ • Rate Display and Control Range: 0 - 999.9 Å/sec • Measurement and Control Update Period: 0.25 sec • Shutter Delay: ±% of Rate Set Point • Power Requirements: 120 / 240 V (+5, -25%), 50 - 60 Hz, 50 VA • Operating Temperature: 0 - 50°C
This Micro Component Technology MCT 6603 Hydrogen Rework Station is used and in excellent condition. This unit was tested with an in-house hydrogen container. It is full working order. Nissho Optical MDS-40 Microscope • Long working distance of 135mm • Standard specification for a total magnification of 10X • Magnification range can be extended from 5X to 40X by selecting auxiliary lenses and eyepieces
Linemaster Treadlite T-51 foot control • 7A, 125-250 VAC~ • Nonskid base pad • Strong steel housing
Please contact manufacturer for pricing and availability of hydrogen containers.
This Coherent / Lambda Physik K2005 248 nm, CaF2, Excimer Laser is used and in excellent condition. This unit was decommissioned from a production facility. We do not have the ability to test this unit and have documented all the information we can gather from it in this page. A very good effort was made to retain accessories. This item will be sold as/is without warranty and will be priced accordingly for parts/repair, although the actual operating condition is unknown. Please see photos below for what is included with this unit.
Photos of the laser and its open panels/electronics are posted near the bottom of this page.
Photos of included accessories: View Photo of controller. View Photo of included accessories. View Photo of parts case. View Photo of accessories inside of parts case, whole layout. View Photo of accessories from inside of parts case, view 1. View Photo of accessories from inside of parts case, view 2. View Photo of accessories from inside of parts case, view 3. View Photo of accessories from inside of parts case, view 4. View Photo of accessories from inside of parts case, view 5. View Photo of accessories from inside of parts case, view 6. View Photo of checklist for parts case. View Photo of circuits and block diagrams. View Photo of software diskettes.
There is a small scratch on the screen cover of this unit; however, this will not affect its ability to function properly. This unit does not include batteries.
Included Accessories: • Hard Sided Case • Battery Charger: CL300 Series, Part Number: 504700 • Probe: Alpha 20 MHz, .25" • Probe Cable: C.D. International BM-174-2 BNC to 1/4-32
This Zygo NewView 200 Interferometer is used and in as-is parts grade condition. This unit is incomplete and is missing the electronic enclosure. The electronic enclosure houses the main instrument board and power supply. It provides power to the microscope and interfaces to the computer. It will be sold as-is without warranty and will be priced accordingly. If you would like to purchase an individual component of this unit, please contact Artisan Technology Group Sales for pricing and availability.
This unit includes: NewView Microscope, Support Stage, Vibration Isolation Table, Computer, Color Display, Video Monitor, Mouse, and Keyboard.
Configuration: • Part Number: 6300-0182-02 • Operating System: HP-UX (A.09.07) • Boot ROM v1.6 • 32 MB RAM • 2.1 GB Hard Disk Drive • MetroPro 7.3.0 Software Installed
This unit includes the operating system software diskette This unit has minor cosmetic scratches on the front which can be seen here and here. The scratches do not impact the operation of this unit.
Included Components: • DI-340 Controller and Computer • LG E2242TA Monitor • Lumetrics 50mm Probe • Lumetrics Verification Probe w/ F1VS200F2.5 Fiber Optic Microscope and Accessories • Probe Stand and Accessories • National Instruments SH68-68-EPM Cable, 2 Meters • Power Cables for Computer, Controller, and Monitor
TMS 63E-563 Micro-g Vibration Lab Table: • BreadBoard: 36" x 48" (LxW) CleanTop II • CleanTop II Thickness: 4" • Screw Type: 1/4-20, 1" Spacing • Stabilizers: Gimbal Piston Air Isolators
This Kevex 952-103 Omicron X-Ray Fluorescence Spectrometer is used and in excellent condition. The unit also includes a monitor for viewing results. This unit was decommissioned from a production facility. A very good effort was made to retain accessories. A 50W source is installed. This unit will need some additional accessories to become complete: PC to Kevex connection cable, etc.
Included Accessories: PC, Mouse Keyboard, CRT Monitor (not shown in photos), Joystick (not shown in photos), X-Ray Warning Lamp, Serial and Power Cabling, Safety Mask and Piping
This EMTS/Electroglas 2001X P/S Automatic Wafer Prober is used and in excellent condition. It includes the cables and accessories listed below and pictured. Computer sold separately. We do not have the expertise to fully test this unit and have documented all the information gathered from it in this page. It is recommended that the purchaser of this system contact the manufacturer for replacement components.
System Configuration:
• Navitar Uni-lite 1x Coaxial Illuminator • DF-150-3 Dark Field Illuminator • Sanyo Black and White Video Monitor (has some screen burn-in artifacts) • Control Keyboard (Missing Enter and Plus Keys) • Joystick Controller and Keypad (Missing Plus key) • Power Source with Camera Lighting Controls • Sola MCR 2000 Power Regulator (not pictured) • (3) 25-slot Wafer Probe Cassette (not pictured)
CIVision Wafer Inspection System:
• Model: 1 Camera Lowmax • CIVision Manual • Software CD: APC PowerChute Personal Edition • Software CD: eVGA Display Driver Installation • Software CD: Measurement Computing • Software CD: Intel Express Installer CD • Software CD: ViewSonic Wizard: User Guide and Installation • Software 3 1/4 Floppy: RAID Driver
Basler A311f Camera:
• Video Output: Mono • Sensor Size 659x494 • Sensor Type: Progressive Scan CCD • Max Frame Rate: 73 Frames/s • Video Output: IEEE 1394
View Photo of the joystick controller. View Photo of the monitor and control keyboard.
This instrument was removed from service and a very good effort was made to keep all of its components and spares together. It will require some accessories (i.e. cabling, hoses, software, computer, camera or other hardware) as well as expertise in setting up such a system to become complete and ready to operate. Please contact manufacturer for pricing and availability of required software and accessories.
Configuration: • (2) Cole-Parmer C/L 2-Channel Variable Speed Pumps and Cole-Parmer Power Supplies • 9.5in x 10in Milling Platform • Internal Lamp • 9-Pin and 25-Pin Cable
This West-Bond 7400E 45 Degree Wire Feed Wedge Bonder is used and in excellent condition.
7400E Configuration: • Processor: Motorola 6800 • Z Tool Range: 0.5625 Inch • Z Encoder Resolution: 0.001 Inch • Bond Force Range: Adjustable, 10 to 250 Grams • Wire Range: 0.7 to 2.0 Mils
This Inficon IC-6000 Vacuum Deposition Controller is used and in good condition. The monitor does not work on the unit; however, the unit functions appropriately when attached to an external monitor.
This Inficon IC-6000 Vacuum Deposition Controller is used and in good condition. The monitor does not work on the unit; however, the unit functions appropriately when attached to an external monitor.
This Alcatel-Lucent High Vacuum Bell Jar System for Thin Film Deposition is used and in excellent condition. This unit is designed to work with an external vacuum pump.
Configuration:
• Bell Jar Diameter: 13 inches • Linear Actuator Displacement: 36 inches • Granville Philips 275 Convectron Gauge • GE Series One Programmable Controller with CPU Series One Plus • Bell Jar Safety Cage • Input Voltage: 120 VAC
View Photo of inside of the unit. View Photo of the GE Series One Programmable Controller and CPU Series One Plus.
This MKS Instruments 247 Four Channel Power Supply / Readout is used and in excellent condition. This unit includes two MKS Instruments CB259-5-10 cables.
247 Configuration: • Display Type: 3 ½ digit 0.56" Red LED, Display is 1 of 4 Sequentially Selectable • Number of Channels: 4 • Signal Inputs from MFC/MFM: 4 x 0-5 VDC • Gas Correction Factor (Scaling): 0.1-4.0 (Rear Panel) • External Set Point: 0-5 VDC • External ON/OFF: TTL-Compatible • Signal Ouputs Unscaled: 4 x 0-5 VDC = 0-100% of F.S. • Signal Outputs Scaled: 0-2 VDC (Max)
This Inficon XTC Thin Film Thickness and Rate Monitor is used and in good condition. This unit is missing the prop stand. This unit does not include rackmount handles. Configuration: • Thickness Display Range: 0 - 999.9 kÅ • Rate Display and Control Range: 0 - 999.9 Å/sec • Measurement and Control Update Period: 0.25 sec • Shutter Delay: ±5% of Rate Set Point • Power Requirements: 120 / 240 V (+5, -25%), 50 - 60 Hz, 50 VA • Operating Temperature: 0 - 50°C
This Inficon XTC Thin Film Thickness and Rate Monitor is used and in good condition. This unit has a dent on the front panel and is missing the prop stand. This unit does not include rackmount handles.
Configuration: • Thickness Display Range: 0 - 999.9 kÅ • Rate Display and Control Range: 0 - 999.9 Å/sec • Measurement and Control Update Period: 0.25 sec • Shutter Delay: ±5% of Rate Set Point • Power Requirements: 120 / 240 V (+5, -25%), 50 - 60 Hz, 50 VA • Operating Temperature: 0 - 50°C
This system appears to be complete. System includes: CRS-3100 Optical Review System, Sony Trinitron Color Video Monitor, Toshiba Image Master Digital Video Printer, Sony Trinitron Multiscan Monitor, Blower, Hoses for Blower, Keyboard and Mouse, Emergency Stop Switch, RGB Video Cables, Toshiba Remote Printer Control, VGA Cable (Box), XYZ Controller. For specific photos of what is included, see bottom of this stock-item.
We do not have the expertise to fully test this unit and have documented all the information gathered from it in this page. It is recommended that the purchaser of this system contact KLA-Tencor for installation, setup and maintenance. A very good effort was made to retain accessories. This item will be sold as/is without warranty and will be priced accordingly. However, if desired, this unit can be inspected on-site. Please contact Artisan Technology Group Sales to set this up.
This unit will ship in several crates. See picture section for photo of crates.
PC Configuration: • Processor: Pentium III 850Mhz • OS: Windows NT 4.0 SP6 • Memory: 265 MB RAM • Hard Drive: 17 GB HDD • Keyboard, Mouse and Monitor Included
Before installing and operating this unit, the coolant lines will need to be completely flushed. In order for unit to operate correctly through the full temperature range, 3M Novec HFE7500 Engineered Fluid needs to be installed. This unit comes with a quick-connect air hose.
The environmental chamber does not have the application specific thermal unit installed. The thermal unit or Tool is the part that makes contact with the Device Under Test, and applies the changes in temperature. A tool will need to be installed according to the specific test being performed. View Photo of the tool installed in the environmental chamber.
Configuration: • Input: 190-230 VAC • Frequency: 50-60 Hz • Phase: 3 • Interrupt Current: 65,000 AIC • Largest Load Ampere Rating: 18 A • Machine Main Breaker Ampere Rating: 30 A • Full Load Amps: 24 A • Temperature Range (Passive): -40°C to +150°C • Temperature Ramp Rate: 100°C Per Second • ESD: <100 V within 6" of device • Communication Interface: GPIB and RS232 • Air: 80 psi, 2-3 scfm, clean, dry dewpoint 15°C below coldest chiller setpoint • Weight: 340 kgs (750 lbs) • Dimensions: 25.4W x 42D x 63H inches (0.65m x 1.08m x 1.62m) • Chiller: Affinity PAG-040K-BE51CBD2 Installed* • Passive Model Version
This system appears to be complete, with the exception of the Signal Light Tower. The system light tower was likely uninstalled when the instrument was decommissioned to fit through a doorway and became orphaned. System includes: CRS-3100 Optical Review System, Sony Trinitron Color Video Monitor, Toshiba Image Master Digital Video Printer, Sony Trinitron Multiscan Monitor, Blower, Hoses for Blower, Keyboard and Mouse, Emergency Stop Switch, RGB Video Cables, Toshiba Remote Printer Control, VGA Cable (Box), XYZ Controller. For specific photos of what is included, see bottom of this stock-item.
We do not have the expertise to fully test this unit and have documented all the information gathered from it in this page. It is recommended that the purchaser of this system contact KLA-Tencor for installation, setup and maintenance. A very good effort was made to retain accessories. This item will be sold as/is without warranty and will be priced accordingly. However, if desired, this unit can be inspected on-site. Please contact Artisan Technology Group Sales to set this up.
This unit will ship in several crates. See picture section for photo of crates.
Signal Light Tower is Not Included
PC Configuration: • Processor: Pentium III 850Mhz • OS: Windows NT 4.0 SP6 • Memory: 265 MB RAM • Hard Drive: 17 GB HDD • Keyboard, Mouse and Monitor Included
This Sigma Instruments EIES-IV Guardian Thin Film Deposition Controller is used and in excellent condition. This version does not have the High-Voltage LED on the front panel.
Probes, AC adapter and batteries are not included. Please contact manufacturer for pricing and availability. There is a slight crack in the case which does not affect functionality.
This Universal Systems / Trio-Tech Stainless Steel Wet Process Station is used and in excellent condition. This wet bench has all the connections and accessories shown in the pictures below. It is a solvent wash station with ultrasonic rinse. Handheld water spray and nitrogen gas spray installed. External Exhaust, CDA (Clean Dry Air), Nitrogen, and Water required for operation.
Model Number: US72 VLF FA-1976
It comes with (2) sweepSONIK 40kHz dualSweep Ultrasonic Generators (the connectors for these are on the bottom rear of unit) both are model number: 40-S2DG-12T-208V-C, a top exhaust fitting, and a plexi-glass top guard.
Main Unit: Controls: 977E Emergency Power Off
Tanks 1 and 3: Operation: Ultrasonic Rinse and Drain Dimensions: 14x10x8.5 in (WxLxD) Controls: Universal 977C Controller w/ Timer Lid Included
Tanks 2 and 4: Operation: QDR Quick Dump and Rinse (Drain) Dimensions: 14x10x8.5 in (WxLxD) Controls: Universal 977T Timer Lid Included
Tank 5: Operation: Washing Station and Drain Dimensions: 14x10x8.5 in (WxLxD) w/ Spillover Ledge Controls: Universal 977T Timer
This PACE TF-2000 BGA / CSP Rework System is a parts unit and will be sold as is without warranty. This unit's lower heating unit is not working properly. The custom connection cables are included. The PC, software, cooling fan, or other attachments are not included. Please contact manufacturer for pricing and availability.
Before installing and operating this unit, the coolant lines will need to be completely flushed. In order for unit to operate correctly through the full temperature range, 3M Novec HFE7500 Engineered Fluid needs to be installed. This unit comes with a quick-connect air hose.
The environmental chamber has an application specific thermal unit installed. The thermal unit or tool is the part that makes contact with the Device Under Test, and applies the change in temperature. This unit does not have a thermal unit installed.
Configuration: • Input: 190-230 VAC • Frequency: 50-60 Hz • Phase: 3 • Interrupt Current: 65,000 AIC • Largest Load Ampere Rating: 33 A • Machine Main Breaker Ampere Rating: 50 A • Full Load Amps: 40 A • Temperature Range (Passive): -30°C to +150°C • Temperature Ramp Rate: 100°C Per Second • ESD: <100 V within 6" of device • Communication Interface: GPIB and RS232 • Air: 80 psi, 2-3 scfm, clean, dry dewpoint 15°C below coldest chiller setpoint • Weight: 340 kgs (750 lbs) • Dimensions: 25.4W x 42D x 63H inches (0.65m x 1.08m x 1.62m) • Chiller: Affinity PAG-040K-BE51CBD2 Installed* • Passive Model Version
This MicroVision MVT 7080 Wafer Sorter is a parts unit and is being sold as is. The unit is incomplete. It has been priced accordingly. We do not have the expertise to fully test this unit and have documented all the information gathered from it in this page.
MVT 7080 Configuration: Holds up to (4) Cassettes Cassettes Not Included PC Controller Not Included
This unit is designed to work with an external vacuum pump. The thermal unit does not lower, but it does raise and pump. Before installing and operating this unit, the coolant lines will need to be completely flushed. In order for unit to operate correctly through the full temperature range, 3M Novec HFE7500 Engineered Fluid needs to be installed. This unit comes with a quick-connect air hose. Also, the unit will come in a custom wooden crate.
The environmental chamber has an application specific thermal unit installed. The thermal unit or tool is the part that makes contact with the Device Under Test, and applies the change in temperature. The tool may need to be changed according to the specific test being performed. View Photo of the tool installed in the environmental chamber.
Configuration: • Input: 190-230 VAC • Frequency: 50-60 Hz • Phase: 3 • Interrupt Current: 65,000 AIC • Largest Load Ampere Rating: 33 A • Machine Main Breaker Ampere Rating: 50 A • Full Load Amps: 40 A • Temperature Range (Passive): -30°C to +150°C • Temperature Ramp Rate: 100°C Per Second • ESD: <100 V within 6" of device • Communication Interface: GPIB and RS232 • Air: 80 psi, 2-3 scfm, clean, dry dewpoint 15°C below coldest chiller setpoint • Weight: 340 kgs (750 lbs) • Dimensions: 25.4W x 42D x 63H inches (0.65m x 1.08m x 1.62m) • Chiller: Affinity PAG-040K-BE51CBD2 Installed* • Passive Model Version
The thermal unit does not raise and lower. Before installing and operating this unit, the coolant lines will need to be completely flushed. In order for unit to operate correctly through the full temperature range, 3M Novec HFE7500 Engineered Fluid needs to be installed. This unit comes with a quick-connect air hose.
The environmental chamber does not have the application specific thermal unit installed. The thermal unit or Tool is the part that makes contact with the Device Under Test, and applies the changes in temperature. A tool will need to be installed according to the specific test being performed. View Photo of the tool installed in the environmental chamber.
Configuration: • Input: 190-230 VAC • Frequency: 50-60 Hz • Phase: 3 • Interrupt Current: 65,000 AIC • Largest Load Ampere Rating: 33 A • Machine Main Breaker Ampere Rating: 50 A • Full Load Amps: 40 A • Temperature Range (Passive): -30°C to +150°C • Temperature Ramp Rate: 100°C Per Second • ESD: <100 V within 6" of device • Communication Interface: GPIB and RS232 • Air: 80 psi, 2-3 scfm, clean, dry dewpoint 15°C below coldest chiller setpoint • Weight: 340 kgs (750 lbs) • Dimensions: 25.4W x 42D x 63H inches (0.65m x 1.08m x 1.62m) • Chiller: Affinity PAG-040K-BE51CBD2 Installed* • Optional Delta Design Power Summing Module Installed • Passive Model Version
Before installing and operating this unit, the coolant lines will need to be completely flushed. In order for unit to operate correctly through the full temperature range, 3M Novec HFE7500 Engineered Fluid needs to be installed. This unit comes with a quick-connect air hose.
The environmental chamber has an application specific thermal unit installed. The thermal unit or tool is the part that makes contact with the Device Under Test, and applies the change in temperature. The tool may need to be changed according to the specific test being performed. View Photo of the tool installed in the environmental chamber.
Configuration: • Input: 190-230 VAC • Frequency: 50-60 Hz • Phase: 3 • Interrupt Current: 65,000 AIC • Largest Load Ampere Rating: 33 A • Machine Main Breaker Ampere Rating: 50 A • Full Load Amps: 40 A • Temperature Range (Passive): -30°C to +150°C • Temperature Ramp Rate: 100°C Per Second • ESD: <100 V within 6" of device • Communication Interface: GPIB and RS232 • Air: 80 psi, 2-3 scfm, clean, dry dewpoint 15°C below coldest chiller setpoint • Weight: 340 kgs (750 lbs) • Dimensions: 25.4W x 42D x 63H inches (0.65m x 1.08m x 1.62m) • Chiller: Affinity PAG-040K-BE51CBD2 Installed* • Optional Delta Design Power Summing Module Installed • Passive Model Version
Before installing and operating this unit, the coolant lines will need to be completely flushed. In order for unit to operate correctly through the full temperature range, 3M Novec HFE7500 Engineered Fluid needs to be installed. This unit comes with a quick-connect air hose.
The environmental chamber has an application specific thermal unit installed. The thermal unit or tool is the part that makes contact with the Device Under Test, and applies the change in temperature. This unit does not have a thermal unit installed.
Configuration: • Input: 190-230 VAC • Frequency: 50-60 Hz • Phase: 3 • Interrupt Current: 65,000 AIC • Largest Load Ampere Rating: 33 A • Machine Main Breaker Ampere Rating: 50 A • Full Load Amps: 40 A • Temperature Range (Passive): -30°C to +150°C • Temperature Ramp Rate: 100°C Per Second • ESD: <100 V within 6" of device • Communication Interface: GPIB and RS232 • Air: 80 psi, 2-3 scfm, clean, dry dewpoint 15°C below coldest chiller setpoint • Weight: 340 kgs (750 lbs) • Dimensions: 25.4W x 42D x 63H inches (0.65m x 1.08m x 1.62m) • Chiller: Affinity PAG-040K-BE51CBD2 Installed* • Optional Delta Design Power Summing Module Installed • Passive Model Version