This American Hofmann OS-1 Optical Scanner is used and in excellent condition.
This MKS Instruments 247 Four Channel Power Supply / Readout is used and in excellent condition.
247 Configuration:
• Display Type: 3 ½ digit 0.56" Red LED, Display is 1 of 4 Sequentially Selectable
• Number of Channels: 4
• Signal Inputs from MFC/MFM: 4 x 0-5 VDC
• Gas Correction Factor (Scaling): 0.1-4.0 (Rear Panel)
• External Set Point: 0-5 VDC
• External ON/OFF: TTL-Compatible
• Signal Outputs Unscaled: 4 x 0-5 VDC = 0-100% of F.S.
• Signal Outputs Scaled: 0-2 VDC (Max)
View Photo of the back of this unit
247 Configuration:
• Display Type: 3 ½ digit 0.56" Red LED, Display is 1 of 4 Sequentially Selectable
• Number of Channels: 4
• Signal Inputs from MFC/MFM: 4 x 0-5 VDC
• Gas Correction Factor (Scaling): 0.1-4.0 (Rear Panel)
• External Set Point: 0-5 VDC
• External ON/OFF: TTL-Compatible
• Signal Outputs Unscaled: 4 x 0-5 VDC = 0-100% of F.S.
• Signal Outputs Scaled: 0-2 VDC (Max)
View Photo of the back of this unit
This American Hofmann OS-1 Optical Scanner is used and in excellent condition.
This Advanced Energy PEII 10 kW Low-Frequency Power Supply is used and in excellent condition.
Older Style PEII-10K:
• P/N: 3157600-000H
• 10 kW Output Power
• 40 kHz Sine Wave Output
• Remote Operation Chassis
This Advanced Energy PEII has an input power of 200-208 V, 36 A, 50/60 Hz, and 3 phase with ground.
Older Style PEII-10K:
• P/N: 3157600-000H
• 10 kW Output Power
• 40 kHz Sine Wave Output
• Remote Operation Chassis
This Advanced Energy PEII has an input power of 200-208 V, 36 A, 50/60 Hz, and 3 phase with ground.
This American Hofmann OS-1 Optical Scanner with cable is used and in excellent condition.
Configuration:
•Cable Length: Approximately 35 in.
Configuration:
•Cable Length: Approximately 35 in.
This unit does not include the Curing Lamp.
Accessories Included:
• 320-390 nm Filter, Part Number: P019-01048R
• 320-500 nm Filter, Part Number: P019-01049R
• Foot Switch
View Photo of accessories included.
Light Guides are Sold Separately here.
Accessories Included:
• 320-390 nm Filter, Part Number: P019-01048R
• 320-500 nm Filter, Part Number: P019-01049R
• Foot Switch
View Photo of accessories included.
Light Guides are Sold Separately here.
This Veeco / Wyko NT1100 Optical Profiler is used and in excellent condition.
• Profiler
• Illuminator control unit
• PC
• Vision 32 Version 2.303 Installed
• Monitor
• Keyboard and mouse
• All necessary cables
• Light source: Tungsten halogen lamp
• Objectives: 20X and 50X
• Video display: monochrome monitor
• Stages: Manual Z stage; X/Y translation
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
System Includes:
• Profiler
• Illuminator control unit
• PC
• Vision 32 Version 2.303 Installed
• Monitor
• Keyboard and mouse
• All necessary cables
Profiler Includes:
• Light source: Tungsten halogen lamp
• Objectives: 20X and 50X
• Video display: monochrome monitor
• Stages: Manual Z stage; X/Y translation
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
This Zygo 8020 ZMI-1000A Displacement Measuring Interferometer System VME Position Board is used and in excellent condition.
Part Number: 8020-0206-01, 8020-0206-01-J
Part Number: 8020-0206-01, 8020-0206-01-J
There is a CyberOptics Semiconductor EX-43-PS-C03 wafer mapping sensor attached to this unit. This unit is also known as the KLA Tencor 0000941-000.
This Dymax 2000-EC UV Curing Light Source Flood Lamp System is used and in excellent condition. This unit includes the 2000-EC Flood, the EC-400 Power Supply, and an interface cable. The ZIP Shutter and the Light Shield are sold separately.
Reported Lamps Hours: Between 200-400 Hours Depending on Unit
Reported Lamps Hours: Between 200-400 Hours Depending on Unit
This unit is also known as Highly Electric EFS-D Foot Switch.
Configuration:
• Voltage: 250 V
• Amperage: 10 A
Configuration:
• Voltage: 250 V
• Amperage: 10 A
Part Number: 670BD81
670BD81 Configuration:
Operates MKS High Accuracy Baratron Pressure Sensors
Remote Interface: GPIB
670BD81 Configuration:
Operates MKS High Accuracy Baratron Pressure Sensors
Remote Interface: GPIB
Configuration:
• Lamp Hours: 155
• Maximum Intensity Output: 19054 mW/cm^2 (350-500nm Bandpass)
Part Number: 012-60850
• Lamp Hours: 155
• Maximum Intensity Output: 19054 mW/cm^2 (350-500nm Bandpass)
Part Number: 012-60850
This unit was pulled from a working environment. A best effort was made to keep this complete. Please see photos for more detail. It ships as photoed.
Part Number: 2-142-04
80F Specs:
• Actuation: Manual
• Max Weld Force: 20 lb (89 N)
• Max Rating: 2 KVA (250 W-s)
• Electrode Diameter: 0.125 in (3.2 mm)
• Electrode Configuration: Opposed
Part Number: 2-142-04
80F Specs:
• Actuation: Manual
• Max Weld Force: 20 lb (89 N)
• Max Rating: 2 KVA (250 W-s)
• Electrode Diameter: 0.125 in (3.2 mm)
• Electrode Configuration: Opposed
Configuration:
• Lamp Hours: 220
• Maximum Intensity Output: 19553 mW/cm^2 (350-500nm Bandpass)
Part Number: 012-60850
• Lamp Hours: 220
• Maximum Intensity Output: 19553 mW/cm^2 (350-500nm Bandpass)
Part Number: 012-60850
This Schmitt Industries TMS 2000 Texture Measurement System is used and in excellent condition. This unit includes computer, monitor, TMS software v3.11, and MESA v3.2.c2.
Computer Info
• OS: Windows NT4.0 and SP6
A PS2 mouse and keyboard are required to make this unit complete.
View Photo of the full texture scan
View Photo of the full surface scan with a low filter
View Photo of the full surface scan data
View Photo of the full scan data
Computer Info
• OS: Windows NT4.0 and SP6
A PS2 mouse and keyboard are required to make this unit complete.
View Photo of the full texture scan
View Photo of the full surface scan with a low filter
View Photo of the full surface scan data
View Photo of the full scan data
This Helmut-Fischer Fischerscope XDAL-FD EDXRF Spectrometer is used and in excellent condition.
Configuration:
• FD: Fast Detector
• Tube: Micro
• Detector: PIN
• Filters: 3
• Aperture: 4
• Probe Placing: XYZ
• CPU: 1.8 Ghz P4, 1GB RAM, 20GB HDD, Windows XP, XDAL-FT Software v6.19 with Monitor, Keyboard and Mouse
Input Voltage: 120 VAC Only
Click here to view the photo of a wafer taken with the device's on-board camera by an Artisan Technology Group technician.
Parts and Accessories:
• (1) FI-SIM WinFTM Super X720 (Security USB Dongle)
• (3) WINFTM V6 CDs (Version: 6.13, 6.14, 6.19)
• (1) Serial Cable for connecting device to computer
• (1) Video Cable for camera
Click here to view a photo of the parts and accessories.
Configuration:
• FD: Fast Detector
• Tube: Micro
• Detector: PIN
• Filters: 3
• Aperture: 4
• Probe Placing: XYZ
• CPU: 1.8 Ghz P4, 1GB RAM, 20GB HDD, Windows XP, XDAL-FT Software v6.19 with Monitor, Keyboard and Mouse
Input Voltage: 120 VAC Only
Click here to view the photo of a wafer taken with the device's on-board camera by an Artisan Technology Group technician.
Parts and Accessories:
• (1) FI-SIM WinFTM Super X720 (Security USB Dongle)
• (3) WINFTM V6 CDs (Version: 6.13, 6.14, 6.19)
• (1) Serial Cable for connecting device to computer
• (1) Video Cable for camera
Click here to view a photo of the parts and accessories.
This This unit is also known as the EFOS Acticure 4000 Ultraviolet / Visable Spot Cure System. This is for the Acticure 4000 unit itself, there are no accessories included.
Configuration:
• Lamp Type: 100 W Mercury Arc lamp
Input Power: 90-264 VAC
Configuration:
• Lamp Type: 100 W Mercury Arc lamp
Input Power: 90-264 VAC
This Dymax 2000-EC UV Curing Light Source Flood Lamp System is used and in excellent condition. This unit includes the 2000-EC Flood and the EC-400 Power Supply. The ZIP Shutter, the Light Shield, and the interface cable are sold separately.
Reported Lamps Hours: Between 200-400 Hours Depending on Unit
Reported Lamps Hours: Between 200-400 Hours Depending on Unit
This Inficon IC-6000 OSC S / S Card is used and in excellent condition.
Part Number: 205-340-B
Part Number: 205-340-B
This unit is incomplete and does not include the built-in radiometer for calibrating the light intensity output. Please contact Exfo for pricing and availability of the radiometer. PC and Novacure Software are not included.
320-500 nm Bandpass Filter Included
Fiber Light Guides are Sold Separately here
320-500 nm Bandpass Filter Included
Fiber Light Guides are Sold Separately here
This Spectronic Spectroline PC-2200A UV EPROM/Wafer Erasing System is used and in excellent condition.
Part Number: UB27115, 1-191-02
Input Voltage: 115 VAC
Input Voltage: 115 VAC
This Zygo ZMI-4004 4-Axis VME64x Measurement Board is used and in excellent condition.
Part Number: 8020-0500, 8020-0500-01, 8020-0500-01-J, 8020-0500-J
Part Number: 8020-0500, 8020-0500-01, 8020-0500-01-J, 8020-0500-J
This Zygo 8030 ZMI-1000 Displacement Measuring Interferometer System VME Position Board is used and in excellent condition.
Part Number: 8030-0200
Part Number: 8030-0200
Configuration:
• Input Voltage: 115VAC
• Air Source: High Efficiency Diaphragm Pump
• Air Flow: Variable, 3-20 1/min
Includes:
• (1) FCR-2200 Base
• (1) FCT-2228 Handpiece
• (1) 18131S FCT Holder
• Input Voltage: 115VAC
• Air Source: High Efficiency Diaphragm Pump
• Air Flow: Variable, 3-20 1/min
Includes:
• (1) FCR-2200 Base
• (1) FCT-2228 Handpiece
• (1) 18131S FCT Holder
This Inficon XTC Thin Film Thickness and Rate Monitor is used and in excellent condition. This unit does not include rackmount handles.
Configuration:
• Thickness Display Range: 0 - 999.9 kÅ
• Rate Display and Control Range: 0 - 999.9 Å/sec
• Measurement and Control Update Period: 0.25 sec
• Shutter Delay: ±5% of Rate Set Point
• Power Requirements: 120 / 240 V (+5, -25%), 50 - 60 Hz, 50 VA
• Operating Temperature: 0 - 50°C
Part Number: 751-001-G1
Configuration:
• Thickness Display Range: 0 - 999.9 kÅ
• Rate Display and Control Range: 0 - 999.9 Å/sec
• Measurement and Control Update Period: 0.25 sec
• Shutter Delay: ±5% of Rate Set Point
• Power Requirements: 120 / 240 V (+5, -25%), 50 - 60 Hz, 50 VA
• Operating Temperature: 0 - 50°C
Part Number: 751-001-G1
This Zygo 8020 ZMI-1000A Displacement Measuring Interferometer System VME Position Board is new from surplus stock.
Part Number: 8020-1206-01, 8020-0206, 8020-0206-01-J
Part Number: 8020-1206-01, 8020-0206, 8020-0206-01-J
Configuration:
• Optional Timer Dial
• Optional Timer Dial
270C-4 Configuration:
• 4½ digit display
• 4½ digit display
This Uthe 228-1 Negative Electric Flame-Off Torch Controller is used and in excellent condition. This 228-1 controller is configured for an S & K torch. S & K torch sold separately.
Part Number: 11U15-0001
228-1 Configuration:
• Constant Output: Current
• Max. Discharge Voltage: 2500V
• Wire Size (microns): 18-38
• Output Current: 20mA
• Recommended EFO GAP: 0.3-0.5mm
Part Number: 11U15-0001
228-1 Configuration:
• Constant Output: Current
• Max. Discharge Voltage: 2500V
• Wire Size (microns): 18-38
• Output Current: 20mA
• Recommended EFO GAP: 0.3-0.5mm
This Dymax 2000-EC UV Curing Light Source Flood Lamp System is used and in excellent condition. This unit includes the 2000-EC Flood, the EC-400 Power Supply, and an interface cable.The ZIP Shutter and the Light Shield are sold separately.
Reported Lamps Hours: Between 20-50 hours Depending on Unit
Reported Lamps Hours: Between 20-50 hours Depending on Unit
This American Hoffmann R-11 Round-Spring Measuring Table is used and in excellent condition. This unit includes one DIN-5c and one DIN-8 connectors.
This Inficon IPN 013-001 Oscillator is used and in excellent condition. It comes with a 6 in OSC cable, part number IPN 013-070.
This Kevex 952-102 Omicron X-Ray Fluorescence Spectrometer is used and in excellent condition. This unit was decommissioned from a production facility. A very good effort was made to retain accessories. A 50W source is installed. This unit will need some additional accessories to become complete: keyboard, mouse, monitor, PC to Kevex connection cable, etc.
Included Accessories: PC, X-Ray Warning Lamp, Serial and Power Cabling, Safety Gloves and Piping
Photos of Accessories: Photo 1 and Photo 2
PC Hardware and Software Info:
• Pentium II MMX, 333 mHz
• 64 MB RAM, 6 GB HDD
• Ultra Link Model 118 ISA Card
• Windows 98
• Omincon v2.21
• Kevex XRF Monitor v7.0
• Kevex SDP (Spectrum Display Panel) v2.1
• Kevex VideoApp v1.0
• Kevex WinXRF v2.21
Input Voltage: 120 VAC Only
Included Accessories: PC, X-Ray Warning Lamp, Serial and Power Cabling, Safety Gloves and Piping
Photos of Accessories: Photo 1 and Photo 2
PC Hardware and Software Info:
• Pentium II MMX, 333 mHz
• 64 MB RAM, 6 GB HDD
• Ultra Link Model 118 ISA Card
• Windows 98
• Omincon v2.21
• Kevex XRF Monitor v7.0
• Kevex SDP (Spectrum Display Panel) v2.1
• Kevex VideoApp v1.0
• Kevex WinXRF v2.21
Input Voltage: 120 VAC Only
This Inficon IC-6000 Vacuum Deposition Controller is used and in excellent condition.
Includes:
• (1) OSC Source S/S Card
• (2) I/O Cards
Includes:
• (1) OSC Source S/S Card
• (2) I/O Cards
This Helmut-Fischer Fischerscope XDL-XYZp Spectrometer is used and in excellent condition. This is the XDL unit only, and does not include computer or software. This unit ships with the holding plate.
View Photo of Holding Plate
Input Voltage: 115 VAC Only
View Photo of Holding Plate
Input Voltage: 115 VAC Only
This Wyko Rough Surface Tester RST-Plus Optical Profilometer is used and in excellent condition. This unit includes: Microscope, Support Stage, Control Boxes, Vibration Isolation Table, Computer, Color Display, Video Monitor, Printer, Joystick, Mouse, and Keyboard.
Computer Configuration:
Processor: Pentium 90 MHz
HDD: 1.24 GB
Memory: 32 MB
OS: Windows 95
Software Installed: Wyko Vision Plus v1.8
Available Filter Settings:
LoMag 0.0 nm
LoMag 650.8 nm
LoMag Clear
HiMag 660.0 nm
HiMag Clear
Monitors Dimensions:
36" W x 59" H x 36" D (91.4cm W x 149.86cm H x 91.4cm D)
Scope Dimensions:
32" W x 59" H x 36" D (81.28cm W x 149.86cm H x 91.4cm D)
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
Computer Configuration:
Processor: Pentium 90 MHz
HDD: 1.24 GB
Memory: 32 MB
OS: Windows 95
Software Installed: Wyko Vision Plus v1.8
Available Filter Settings:
LoMag 0.0 nm
LoMag 650.8 nm
LoMag Clear
HiMag 660.0 nm
HiMag Clear
Monitors Dimensions:
36" W x 59" H x 36" D (91.4cm W x 149.86cm H x 91.4cm D)
Scope Dimensions:
32" W x 59" H x 36" D (81.28cm W x 149.86cm H x 91.4cm D)
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
This Inficon XTM Thin Film Deposition Monitor is used and in excellent condition. This unit includes a D/A cable.
This Metcal APR-5000 Array Package Rework System Base Unit is used and in excellent condition. This unit ships as photoed and with accessories explicitly listed. It does not include additional accessories nor does it include software. Contact manufacturer for pricing and availability for additional accessories and software.
Configuration:
• Voltage: 115/230 VAC
• Version: Breaker
Includes:
• (1) Set of 3 Dip Transfer Plates, Apertures 28, 35, and 45 mm, Depth 0.012" (0.30 mm); Part Number: DTP-BGA
• (2) DTP Plates
• (1) Adjustable "V" Block for CSP Components, Part Number: 20987
• (1) Vacuum Pick-Up Nozzle, 12mm O/D; Part Number: VNZ-12
• (1) Calibration Kit
• (1) Nitrogen/Shop Air Input Cable
• (1) Video In Cable
• (1) RS-232 Cable
• (1) Power Supply Cable
View Photo of accessories.
If you would like to purchase an individual component of this unit, please contact Artisan Technology Group Sales for pricing and availability.
Configuration:
• Voltage: 115/230 VAC
• Version: Breaker
Includes:
• (1) Set of 3 Dip Transfer Plates, Apertures 28, 35, and 45 mm, Depth 0.012" (0.30 mm); Part Number: DTP-BGA
• (2) DTP Plates
• (1) Adjustable "V" Block for CSP Components, Part Number: 20987
• (1) Vacuum Pick-Up Nozzle, 12mm O/D; Part Number: VNZ-12
• (1) Calibration Kit
• (1) Nitrogen/Shop Air Input Cable
• (1) Video In Cable
• (1) RS-232 Cable
• (1) Power Supply Cable
View Photo of accessories.
If you would like to purchase an individual component of this unit, please contact Artisan Technology Group Sales for pricing and availability.
Configuration:
• Lamp Hours: 178
• Maximum Intensity Output: 16880 mW/cm^2 (350-500nm Bandpass)
Part Number: 012-60850
• Lamp Hours: 178
• Maximum Intensity Output: 16880 mW/cm^2 (350-500nm Bandpass)
Part Number: 012-60850
This unit is incomplete and does not include the bandpass filter or fiber light guide.
Fiber Light Guides are Sold Separately here
Fiber Light Guides are Sold Separately here
Configuration:
• Lamp Hours: Unknown
Part Number: 012-64000
• Lamp Hours: Unknown
Part Number: 012-64000
This is also known as the EXFO 012-60850 100-Watt Mercury Arc with Intelli-Lamp Technology.
Configuration:
• Lamp Hours: 333
• Maximum Intensity Output: 18755 mW/cm2 (350-500nm Bandpass)
Part Number: 012-60850
Configuration:
• Lamp Hours: 333
• Maximum Intensity Output: 18755 mW/cm2 (350-500nm Bandpass)
Part Number: 012-60850
This PACE TF-2000 BGA / CSP Rework System is used and in good condition. The PC, software, connection cables, cooling fan, or other attachements are not included. Please contact manufacturer for pricing and availability.
System Configuration:
• Base Station: TF 2000BE
• Reflow Station: TF 2000R
• Placement Station: TF 2000P
• Input Voltage: 230VAC
System Configuration:
• Base Station: TF 2000BE
• Reflow Station: TF 2000R
• Placement Station: TF 2000P
• Input Voltage: 230VAC
This West-Bond K-1400 4 Watt Ultrasonic Generator is used and in excellent condition.
K-1400 Configuration:
• Output Power (Low Side): 0 to 2 W
• Output Power (High Side): 0 to 5 W
• Output Frequency: 62 to 66 KHz, automatically tracked
• Short Setting Time Range: 1 ms to 100 ms
• Long Setting Time Range: 20 ms to 1 sec.
• Required Transducer Impedance: 20 ohms nominal
Input Voltage: 230 VAC
K-1400 Configuration:
• Output Power (Low Side): 0 to 2 W
• Output Power (High Side): 0 to 5 W
• Output Frequency: 62 to 66 KHz, automatically tracked
• Short Setting Time Range: 1 ms to 100 ms
• Long Setting Time Range: 20 ms to 1 sec.
• Required Transducer Impedance: 20 ohms nominal
Input Voltage: 230 VAC
This Dymax EC-400 Power Supply is used and in excellent condition.
Reported Lamps Hours: Between 7700-7900 hours Depending on Unit
Reported Lamps Hours: Between 7700-7900 hours Depending on Unit
This Wyko Rough Surface Tester RST-Plus Rough Surface Tester Optical Profilometer is used and in excellent condition. This unit includes: Microscope, Support Stage, Control Boxes, Computer, Color Display, Illuminator Lamp, Mouse, and Keyboard.
Computer Configuration:
Processor: Pentium 90 MHz
Memory: 32 MB
OS: Windows 95
Software Installed: Wyko Vision Plus v1.8
Filter Options:
• None
Installed Objectives:
• RX2.5
• RX10
• RX40
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
Computer Configuration:
Processor: Pentium 90 MHz
Memory: 32 MB
OS: Windows 95
Software Installed: Wyko Vision Plus v1.8
Filter Options:
• None
Installed Objectives:
• RX2.5
• RX10
• RX40
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
This LeCroy DDA-120 4-Channel, 8 GS/s, 16-bit, 1GHz Bandwidth Oscilloscope is used and in excellent condition.
This unit reports the following options:
• Soft Version: DDA-120 9.3.0
• Scope ID: 3DE478-A0
• Installed Option Key: 9D8E-60C9-AEF7-18B1
• Options Enabled by this Key: MC01
• Opt WP01: Advanced Waveform Math Package Installed
• Opt WP02: Spectrum Analysis Package Installed
• Opt WP03: Parameter Analysis Package Installed
• Opt DDM: Disk Drive Measurements Installed
• Opt CKIO: Clock In/Out Installed
• Opt PRML: Supplementary Disk Drive Measurements Installed
• Opt DDFA: Disk Drive Failure Analysis Installed
• Opt MC01: Memory Card Reader and 512k SRAM Card Installed
• Opt CPUP: PowerPC High Speed Processor Installed
• Opt VGAC: VGA Output Port Installed
• Opt GPIB: IEEE-488 I/O Control Bus Installed
• Opt R232: Serial I/O Installed
• Opt CLBZ: Piezo Buzzer Alarm Installed
• Opt FD01: Floppy Drive Installed
• Opt GP01: Internal Graphics Printer Installed
• Opt CENT: Parallel Centronics Printer Port Installed
• Opt CKTR: Clock Trigger Installed
• Opt I2C: ProBus Installed
• Main Processor Ram: 64 MB
• Acquisition Memory Size: 4M data points per channel
• Trigger Options: AUTO, NORMAL, SINGLE, STOP
• PC Card (PCMCIA I/II/III Ports): for memory cards
• Floppy Disk Drive
• Grid Styles: Single, Dual, Quad, Octal, and Full Screen
• Plotter: Internal, high resolution graphics printer (standard)
• External Monitor: Rear panel 15-pin socket for VGA compatible monitor
• Max Input Voltages: 50 Ohms - 5VDC; 1Mohm - 400V max
This unit reports the following options:
• Soft Version: DDA-120 9.3.0
• Scope ID: 3DE478-A0
• Installed Option Key: 9D8E-60C9-AEF7-18B1
• Options Enabled by this Key: MC01
• Opt WP01: Advanced Waveform Math Package Installed
• Opt WP02: Spectrum Analysis Package Installed
• Opt WP03: Parameter Analysis Package Installed
• Opt DDM: Disk Drive Measurements Installed
• Opt CKIO: Clock In/Out Installed
• Opt PRML: Supplementary Disk Drive Measurements Installed
• Opt DDFA: Disk Drive Failure Analysis Installed
• Opt MC01: Memory Card Reader and 512k SRAM Card Installed
• Opt CPUP: PowerPC High Speed Processor Installed
• Opt VGAC: VGA Output Port Installed
• Opt GPIB: IEEE-488 I/O Control Bus Installed
• Opt R232: Serial I/O Installed
• Opt CLBZ: Piezo Buzzer Alarm Installed
• Opt FD01: Floppy Drive Installed
• Opt GP01: Internal Graphics Printer Installed
• Opt CENT: Parallel Centronics Printer Port Installed
• Opt CKTR: Clock Trigger Installed
• Opt I2C: ProBus Installed
• Main Processor Ram: 64 MB
• Acquisition Memory Size: 4M data points per channel
• Trigger Options: AUTO, NORMAL, SINGLE, STOP
• PC Card (PCMCIA I/II/III Ports): for memory cards
• Floppy Disk Drive
• Grid Styles: Single, Dual, Quad, Octal, and Full Screen
• Plotter: Internal, high resolution graphics printer (standard)
• External Monitor: Rear panel 15-pin socket for VGA compatible monitor
• Max Input Voltages: 50 Ohms - 5VDC; 1Mohm - 400V max
This KLA Tencor SFS-7600 Surfscan Patterned Wafer Inspection System is used and in good condition. We do not have the expertise to fully test this unit and have documented all the information gathered from it in this page. It is recommended that the purchaser of this system contact KLA-Tencor for installation, setup and maintenance. A very good effort was made to retain accessories. This item will be sold as/is without warranty and will be priced accordingly. However, if desired, this unit can be inspected on-site. Please contact Artisan Technology Group Sales to set this up.
The aligner operated on boot up and the internal fixture accepted a 200mm wafer. The aligner takes 100, 125, 150, and 200mm wafers however the internal fixture will only take 200mm wafers; wafer racks are sold separately. The system needs both a vacuum and air source to operate. The right side keyboard door hinge is broken and the keyboard is missing two keys however this does not affect its functionality. Service screen indicates that the laser will need to be replaced. You can view image of the keyboard and service screen shot using the links below.
• Processor: 66MHz
• RAM: 23 MB
• HDD: 850 MB
• SFS: 7x00 Series Software Ver. 3.5.0
View Photo of Keyboard
Surfscan 7600 Screen Shots (pdf)
The aligner operated on boot up and the internal fixture accepted a 200mm wafer. The aligner takes 100, 125, 150, and 200mm wafers however the internal fixture will only take 200mm wafers; wafer racks are sold separately. The system needs both a vacuum and air source to operate. The right side keyboard door hinge is broken and the keyboard is missing two keys however this does not affect its functionality. Service screen indicates that the laser will need to be replaced. You can view image of the keyboard and service screen shot using the links below.
PC Configuration:
• Processor: 66MHz
• RAM: 23 MB
• HDD: 850 MB
Software:
• SFS: 7x00 Series Software Ver. 3.5.0
View Photo of Keyboard
Surfscan 7600 Screen Shots (pdf)
270D-4 Configuration:
• 4½ digit display
• CE Mark (Better RF Immunity)
• 4½ digit display
• CE Mark (Better RF Immunity)
This MKS Instruments 246 Single Channel Power Supply / Readout is used and in excellent condition.
246 Configuration:
• Display Type: 3 ½ digit 0.56" Red LED, Continuous Display
• Number of Channels: 1
• Signal Inputs from MFC/MFM: 1 x 0-5 VDC
• Gas Correction Factor (Scaling): 0.1-4.0 (Rear Panel)
• External Set Point: 0-5 VDC
• External ON/OFF: TTL-Compatible
• RS-232: N/A
• Signal Ouputs Unscaled: 1 x 0-5 VDC = 0-100% of F.S.
• Signal Outputs Scaled: 0-2 VDC (Max)
View Photo of the back of this unit
246 Configuration:
• Display Type: 3 ½ digit 0.56" Red LED, Continuous Display
• Number of Channels: 1
• Signal Inputs from MFC/MFM: 1 x 0-5 VDC
• Gas Correction Factor (Scaling): 0.1-4.0 (Rear Panel)
• External Set Point: 0-5 VDC
• External ON/OFF: TTL-Compatible
• RS-232: N/A
• Signal Ouputs Unscaled: 1 x 0-5 VDC = 0-100% of F.S.
• Signal Outputs Scaled: 0-2 VDC (Max)
View Photo of the back of this unit
This Nor-Cal ESVP-1502-NWB Pneumatic Angle Valve is used and in excellent condition.
Configuration
• Type: NW-40B
• Port OD: 1.5 Inches
• Actuation: NC - Air to Open, Spring to Close
Configuration
• Type: NW-40B
• Port OD: 1.5 Inches
• Actuation: NC - Air to Open, Spring to Close
UV bulbs included with this unit are used.
Configuration:
• Wavelength: 254 nm
• (5) Bulbs: 8W SW, BLE-8T254
Input Voltage: 120 VAC Only
Configuration:
• Wavelength: 254 nm
• (5) Bulbs: 8W SW, BLE-8T254
Input Voltage: 120 VAC Only
Part Number: 353-502
This Zygo ZMI-2002 Dual Axis 6U VME Measurement Board is used and in excellent condition.
This Leybold DN 16 ISO-KF Angle Valve is used and in excellent condition.
Configuration:
• Stainless Steel Housing
• FPM Seals
• Supply Voltage: 100V ... 230V
• Frequency: 50 ... 60Hz
• Pickup-/Holding Power: 405/8.1 W
• Opening Time: 100 ms
• Closing Time: 240 ms
• Dead Time: 50 ms
• Conductance 4 l/s
Part Number: 28865
Configuration:
• Stainless Steel Housing
• FPM Seals
• Supply Voltage: 100V ... 230V
• Frequency: 50 ... 60Hz
• Pickup-/Holding Power: 405/8.1 W
• Opening Time: 100 ms
• Closing Time: 240 ms
• Dead Time: 50 ms
• Conductance 4 l/s
Part Number: 28865
This Zygo 8020 ZMI-1000 Displacement Measuring Interferometer System VME Position Board is used and in excellent condition.
Part Number: 8020-0200
Part Number: 8020-0200
PC Configuration:
• OS: Windows 98 SE
• Processor: Intel Celeron
• Memory: 32MB RAM
• Hard Drive: 4 GB HDD
• Keyboard, mouse, and Monitor Included
Software Installed:
• Chip Unzip 2.0
• EMCO WinNC, GE Fanuc Series Ver 13.3
• Smart Cam Connection 11.5
• CamCad Connection 7.6
• DFX Cam connection 7.6
• Production milling 11.5
• Visual CTK 11.0
• IGES Cam connection 7.6
Included Accessories:
View Photo of Low Speed Endmill
View Photo of High Speed Spindle and Renishaw MP15
View Photo of Machine Tool Coolant
View Photo of Included Manuals
This unit does not include a CCD camera.
• OS: Windows 98 SE
• Processor: Intel Celeron
• Memory: 32MB RAM
• Hard Drive: 4 GB HDD
• Keyboard, mouse, and Monitor Included
Software Installed:
• Chip Unzip 2.0
• EMCO WinNC, GE Fanuc Series Ver 13.3
• Smart Cam Connection 11.5
• CamCad Connection 7.6
• DFX Cam connection 7.6
• Production milling 11.5
• Visual CTK 11.0
• IGES Cam connection 7.6
Included Accessories:
View Photo of Low Speed Endmill
View Photo of High Speed Spindle and Renishaw MP15
View Photo of Machine Tool Coolant
View Photo of Included Manuals
This unit does not include a CCD camera.
This Inficon / Sigma Instruments EIES-IV Guardian Thin Film Deposition Controller is used and in excellent condition. This version features a High-Voltage LED on the front panel.
Part Number: 900-051
Part Number: 900-051
This Inficon XTC Thin Film Thickness and Rate Monitor is used and in excellent condition. This unit comes with the 007-251 oscillator kit and extra BNC cables.
Configuration:
• Thickness Display Range: 0 - 999.9 kÅ
• Rate Display and Control Range: 0 - 999.9 Å/sec
• Measurement and Control Update Period: 0.25 sec
• Shutter Delay: ±5% of Rate Set Point
• Power Requirements: 120 / 240 V (+5, -25%), 50 - 60 Hz, 50 VA
• Operating Temperature: 0 - 50°C
View Photo of oscillator kit.
View Photo of extra BNC cables.
Part Number: 751-001-G1
Configuration:
• Thickness Display Range: 0 - 999.9 kÅ
• Rate Display and Control Range: 0 - 999.9 Å/sec
• Measurement and Control Update Period: 0.25 sec
• Shutter Delay: ±5% of Rate Set Point
• Power Requirements: 120 / 240 V (+5, -25%), 50 - 60 Hz, 50 VA
• Operating Temperature: 0 - 50°C
View Photo of oscillator kit.
View Photo of extra BNC cables.
Part Number: 751-001-G1
This Inficon IC-6000 Vacuum Deposition Controller is used and in excellent condition.
Includes:
• (1) Interface Card
• (4) OSC Source S/S Cards
• (2) I/O Cards
• (1) DAC Card
Includes:
• (1) Interface Card
• (4) OSC Source S/S Cards
• (2) I/O Cards
• (1) DAC Card
This Leybold / Inficon OGC 1 Partial Pressure Controller is used and in excellent condition.
Includes:
• (1) I/O Relay Card
• (1) Valve Drive Card
• (1) Video Card
• (1) RS232 CPU Card
• (1) SCU CTL Card
Part Number: 754-003-G1
Includes:
• (1) I/O Relay Card
• (1) Valve Drive Card
• (1) Video Card
• (1) RS232 CPU Card
• (1) SCU CTL Card
Part Number: 754-003-G1
This Wyko Rough Surface Tester RST-Plus Rough Surface Tester Optical Profilometer is used and in excellent condition. This unit includes: Microscope, Support Stage, Control Boxes, Vibration Isolation Table, Computer, Illuminator Lamp, Printer, Mouse, and Keyboard.
Computer Configuration:
Processor: Pentium 166 MHz
Memory: 32 MB
OS: Windows 95
Software Installed: Wyko Vision Plus v1.8
Filter Options:
• None
Installed Objectives:
• L-RX2.5
• RX10
• RX20
• RX40
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
Computer Configuration:
Processor: Pentium 166 MHz
Memory: 32 MB
OS: Windows 95
Software Installed: Wyko Vision Plus v1.8
Filter Options:
• None
Installed Objectives:
• L-RX2.5
• RX10
• RX20
• RX40
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
This Kevex 952-102 Omicron X-Ray Fluorescence Spectrometer is used and in excellent condition. The unit also includes a monitor for viewing results. This unit was decommissioned from a production facility. A very good effort was made to retain accessories. A 50W source is installed. This unit will need some additional accessories to become complete: PC to Kevex connection cable, etc.
Included Accessories: PC, Mouse Keyboard, CRT Monitor (not shown in photos), Joystick (not shown in photos), X-Ray Warning Lamp, Serial and Power Cabling, Safety Mask and Piping
Photos of Accessories: Photo 1 and Photo 2
PC Hardware and Software Info:
• Pentium II MMX, 333 mHz
• 32 MB RAM, 2 GB HDD
• Ultra Link Model 116D ISA Card
• Windows 98
• Omnicron 2.10
• Omincron 2.20
• Kevex XRF monitor 7.0
Input Voltage: 120 VAC Only
Included Accessories: PC, Mouse Keyboard, CRT Monitor (not shown in photos), Joystick (not shown in photos), X-Ray Warning Lamp, Serial and Power Cabling, Safety Mask and Piping
Photos of Accessories: Photo 1 and Photo 2
PC Hardware and Software Info:
• Pentium II MMX, 333 mHz
• 32 MB RAM, 2 GB HDD
• Ultra Link Model 116D ISA Card
• Windows 98
• Omnicron 2.10
• Omincron 2.20
• Kevex XRF monitor 7.0
Input Voltage: 120 VAC Only
This unit is also known as the EXFO P1001-A Ultracure 100SS Plus UV Curing Module. This unit has a high pressure mercury lamp, which is used and has unknown remaining life. The remote cable is not included.
Light Guides are Sold Separately here
Light Guides are Sold Separately here
This unit ships with accessories.
Accessories:
• Personality Board (16058-60003) as seen here
• Socket Board for Transistors (16058-60005) as seen here
• 28-Pin Dual In-Line Socket Board (16147-60002) as seen here
• 18-Pin Dual In-Lin Socket Board (16058-60007) as seen here
• (12) Miniature Banana Plug-Pin Leads (16058-61600) as seen here
• (8) Miniature Pin Plug-Pin Lead (16058-61601) as seen here
• (8) Miniature Clip Lead (16058-61602) as seen here
Accessories:
• Personality Board (16058-60003) as seen here
• Socket Board for Transistors (16058-60005) as seen here
• 28-Pin Dual In-Line Socket Board (16147-60002) as seen here
• 18-Pin Dual In-Lin Socket Board (16058-60007) as seen here
• (12) Miniature Banana Plug-Pin Leads (16058-61600) as seen here
• (8) Miniature Pin Plug-Pin Lead (16058-61601) as seen here
• (8) Miniature Clip Lead (16058-61602) as seen here
This unit is also known as the EFOS Novacure N2001-A1 Spot Curing System.
Options Installed
320-500 nm Filter
Lamp Life Upgrade
PC and Novacure Software are not included
NR5000 Radiometer Upgrade
EMC Upgrade
StepCure
Fiber Light Guides are Sold Separately here
Options Installed
320-500 nm Filter
Lamp Life Upgrade
PC and Novacure Software are not included
NR5000 Radiometer Upgrade
EMC Upgrade
StepCure
Fiber Light Guides are Sold Separately here
This unit includes a DN 40 CF-R Flange.
Configuration:
• Seal with Center Ring and Filter
BPG400 Part Number: 353-502
Sensor Part Number: 354-491
Configuration:
• Seal with Center Ring and Filter
BPG400 Part Number: 353-502
Sensor Part Number: 354-491
This Inficon XTC Thin Film Thickness and Rate Monitor is used and in excellent condition. This module is a combination of (2) Inficon XTC Controllers. These controllers can be sold separately if required. Please contact Artisan Technology Group sales for pricing and availability.
Configuration:
• Thickness Display Range: 0 - 999.9 kÅ
• Rate Display and Control Range: 0 - 999.9 Å/sec
• Measurement and Control Update Period: 0.25 sec
• Shutter Delay: ±% of Rate Set Point
• Power Requirements: 120 / 240 V (+5, -25%), 50 - 60 Hz, 50 VA
• Operating Temperature: 0 - 50°C
Part Number: 751-001-G1
Configuration:
• Thickness Display Range: 0 - 999.9 kÅ
• Rate Display and Control Range: 0 - 999.9 Å/sec
• Measurement and Control Update Period: 0.25 sec
• Shutter Delay: ±% of Rate Set Point
• Power Requirements: 120 / 240 V (+5, -25%), 50 - 60 Hz, 50 VA
• Operating Temperature: 0 - 50°C
Part Number: 751-001-G1
This unit ships with accessories.
Accessories:
• (1) Blank Teflon Board (16058-60004) as seen here.
• (1) Personality Board (16058-60003) as seen here.
• (1) 18-Pin Dual In-Line Socket Board (16058-60007) as seen here.
• (1) 28-Pin Dual In-Line Socket Board (16147-60002) as seen here.
• (2) Diodes Socket Board (16058-60008) as seen here.
• (1) 8-Pin Socket Board (16058-60009) as seen here.
• (1) 10-Pin Socket Board (16058-60010) as seen here.
• (1) 12-Pin Socket Board (16058-60011) as seen here.
• (14) Miniature Banana Plug-Pin Leads (16058-61600) as seen here.
• (8) Miniature Pin Plug-Pin Lead (16058-61601) as seen here.
• (8) Miniature Clip Lead (16058-61602) as seen here.
• (1) 24-Pin Male System Cable (16058-61604) as seen here.
• Accessory Case (16058-60100) as seen here.
Accessories:
• (1) Blank Teflon Board (16058-60004) as seen here.
• (1) Personality Board (16058-60003) as seen here.
• (1) 18-Pin Dual In-Line Socket Board (16058-60007) as seen here.
• (1) 28-Pin Dual In-Line Socket Board (16147-60002) as seen here.
• (2) Diodes Socket Board (16058-60008) as seen here.
• (1) 8-Pin Socket Board (16058-60009) as seen here.
• (1) 10-Pin Socket Board (16058-60010) as seen here.
• (1) 12-Pin Socket Board (16058-60011) as seen here.
• (14) Miniature Banana Plug-Pin Leads (16058-61600) as seen here.
• (8) Miniature Pin Plug-Pin Lead (16058-61601) as seen here.
• (8) Miniature Clip Lead (16058-61602) as seen here.
• (1) 24-Pin Male System Cable (16058-61604) as seen here.
• Accessory Case (16058-60100) as seen here.
This system cable has 24-pin male connectors used to connect the Vm and Vs channels of the 4145A to the 16058A. This cable enables the 4145A to detect whether the fixture lid is open or closed.
This Micro Component Technology MCT 6603 Hydrogen Rework Station is used and in excellent condition. This unit was tested with an in-house hydrogen container. It is full working order.
Nissho Optical MDS-40 Microscope
• Long working distance of 135mm
• Standard specification for a total magnification of 10X
• Magnification range can be extended from 5X to 40X by selecting auxiliary lenses and eyepieces
Linemaster Treadlite T-51 foot control
• 7A, 125-250 VAC~
• Nonskid base pad
• Strong steel housing
Please contact manufacturer for pricing and availability of hydrogen containers.
Nissho Optical MDS-40 Microscope
• Long working distance of 135mm
• Standard specification for a total magnification of 10X
• Magnification range can be extended from 5X to 40X by selecting auxiliary lenses and eyepieces
Linemaster Treadlite T-51 foot control
• 7A, 125-250 VAC~
• Nonskid base pad
• Strong steel housing
Please contact manufacturer for pricing and availability of hydrogen containers.
This Coherent / Lambda Physik K2005 248 nm, CaF2, Excimer Laser is used and in excellent condition. This unit was decommissioned from a production facility. We do not have the ability to test this unit and have documented all the information we can gather from it in this page. A very good effort was made to retain accessories. This item will be sold as/is without warranty and will be priced accordingly for parts/repair, although the actual operating condition is unknown. Please see photos below for what is included with this unit.
Model: Novaline K2005
Manufacture Year: 2001
Input Voltage: 380-400 VAC, 3 Phase, 50-60 Hz
Installed Laser: KrF
Laser Wavelength: 248 nm
Photos of the laser and its open panels/electronics are posted near the bottom of this page.
Photos of included accessories:
View Photo of controller.
View Photo of included accessories.
View Photo of parts case.
View Photo of accessories inside of parts case, whole layout.
View Photo of accessories from inside of parts case, view 1.
View Photo of accessories from inside of parts case, view 2.
View Photo of accessories from inside of parts case, view 3.
View Photo of accessories from inside of parts case, view 4.
View Photo of accessories from inside of parts case, view 5.
View Photo of accessories from inside of parts case, view 6.
View Photo of checklist for parts case.
View Photo of circuits and block diagrams.
View Photo of software diskettes.
Model: Novaline K2005
Manufacture Year: 2001
Input Voltage: 380-400 VAC, 3 Phase, 50-60 Hz
Installed Laser: KrF
Laser Wavelength: 248 nm
Photos of the laser and its open panels/electronics are posted near the bottom of this page.
Photos of included accessories:
View Photo of controller.
View Photo of included accessories.
View Photo of parts case.
View Photo of accessories inside of parts case, whole layout.
View Photo of accessories from inside of parts case, view 1.
View Photo of accessories from inside of parts case, view 2.
View Photo of accessories from inside of parts case, view 3.
View Photo of accessories from inside of parts case, view 4.
View Photo of accessories from inside of parts case, view 5.
View Photo of accessories from inside of parts case, view 6.
View Photo of checklist for parts case.
View Photo of circuits and block diagrams.
View Photo of software diskettes.
There is a small scratch on the screen cover of this unit; however, this will not affect its ability to function properly. This unit does not include batteries.
Included Accessories:
• Hard Sided Case
• Battery Charger: CL300 Series, Part Number: 504700
• Probe: Alpha 20 MHz, .25"
• Probe Cable: C.D. International BM-174-2 BNC to 1/4-32
View Photo of scratch on display cover.
Included Accessories:
• Hard Sided Case
• Battery Charger: CL300 Series, Part Number: 504700
• Probe: Alpha 20 MHz, .25"
• Probe Cable: C.D. International BM-174-2 BNC to 1/4-32
View Photo of scratch on display cover.
This unit is also known as the EFOS Novacure N2001-A1 Spot Curing System.
Configuration:
320-500 nm Filter
PC and Novacure Software are not included
Lamp not included
Radiometer is Included
Light Guides are Sold Separately here
Configuration:
320-500 nm Filter
PC and Novacure Software are not included
Lamp not included
Radiometer is Included
Light Guides are Sold Separately here
This Zygo NewView 200 Interferometer is used and in as-is parts grade condition. This unit is incomplete and is missing the electronic enclosure. The electronic enclosure houses the main instrument board and power supply. It provides power to the microscope and interfaces to the computer. It will be sold as-is without warranty and will be priced accordingly. If you would like to purchase an individual component of this unit, please contact Artisan Technology Group Sales for pricing and availability.
This unit includes: NewView Microscope, Support Stage, Vibration Isolation Table, Computer, Color Display, Video Monitor, Mouse, and Keyboard.
Configuration:
• Part Number: 6300-0182-02
• Operating System: HP-UX (A.09.07)
• Boot ROM v1.6
• 32 MB RAM
• 2.1 GB Hard Disk Drive
• MetroPro 7.3.0 Software Installed
This unit includes: NewView Microscope, Support Stage, Vibration Isolation Table, Computer, Color Display, Video Monitor, Mouse, and Keyboard.
Configuration:
• Part Number: 6300-0182-02
• Operating System: HP-UX (A.09.07)
• Boot ROM v1.6
• 32 MB RAM
• 2.1 GB Hard Disk Drive
• MetroPro 7.3.0 Software Installed
Includes:
• ERSASCOPE Stand
• Bifurcated Light Fiber
• Tokyo Electronic CS6460N CCD Camera (Type TK6788A6)
• X-Y Inspection Table
• S-Video (C/Y) Cable
• 5-Pin Remote Light Source Cable
12 VDC Adapter and Light Source are sold separately.
Part Number: VSSC 100 N
• ERSASCOPE Stand
• Bifurcated Light Fiber
• Tokyo Electronic CS6460N CCD Camera (Type TK6788A6)
• X-Y Inspection Table
• S-Video (C/Y) Cable
• 5-Pin Remote Light Source Cable
12 VDC Adapter and Light Source are sold separately.
Part Number: VSSC 100 N
Configuration:
• Lamp Hours: 40
• Maximum Intensity Output: 16880 mW/cm2 (350-500nm Bandpass)
Part Number: 012-65000
• Lamp Hours: 40
• Maximum Intensity Output: 16880 mW/cm2 (350-500nm Bandpass)
Part Number: 012-65000
UV bulbs included with this unit are used.
Configuration:
• Wavelength: 365 nm
• (6) Bulbs: 15W LW, BLE-1T151
Input Voltage: 120 VAC Only
Configuration:
• Wavelength: 365 nm
• (6) Bulbs: 15W LW, BLE-1T151
Input Voltage: 120 VAC Only
This unit is also known as the EFOS Novacure N2001-A1 Spot Curing System. This unit has a torn faceplate; however, this will not prevent it from functioning properly.
Configuration:
320-500 nm Filter
PC and Novacure Software are not included
Lamp not included
Radiometer is Not Included
Fiber Light Guides are Sold Separately here
View Representative Photo of the torn faceplate.
Configuration:
320-500 nm Filter
PC and Novacure Software are not included
Lamp not included
Radiometer is Not Included
Fiber Light Guides are Sold Separately here
View Representative Photo of the torn faceplate.
Configuration:
• (2) Cables Included - Meant to connect to the UTX-1100 Wafer Robot
• UTC-P / UTC-S Module Installed
• RS232C-1 / EXT-1 Module Installed
• EXT-2 Module Installed
• Input Voltage: 115 VAC Only
• (2) Cables Included - Meant to connect to the UTX-1100 Wafer Robot
• UTC-P / UTC-S Module Installed
• RS232C-1 / EXT-1 Module Installed
• EXT-2 Module Installed
• Input Voltage: 115 VAC Only
270C-4-S Configuration:
• 4½ digit display
• Gauge Factor Switch / Engineering Unit Switch
• 4½ digit display
• Gauge Factor Switch / Engineering Unit Switch
This cable is the miniature banana plugs to the pin plug leads for connecting measurement terminals to the Connection Switch on the Personality Board, or for connecting measurement terminals to the Socket Board.
This HDI Instrumentation IPS-6000 / SRA-FA Hard Disk Surface Reflectance Analyzer and Controller is used and in excellent condition. The unit comes in two parts, the controller-processor unit, and the hard drive platter surface analyzer. All the necessary cables needed to operate this instrument are included. The software needed to run is loaded onto the system hard drive. Upon request, a Ghost Image of the hard disk can be provided by Artisan Technology Group for system software backup and restore.
An Artisan Technology Group technician and Engineer tested this system and successfully ran many types of scans on spare hard disk platters from our lab that were scratched and scribed. The results of theses tests as well as their interaction with the system's software was well documented. This document was created for download by our technicians:
HDI SRA FA Test Results and Function Document Made by ATG Technicians (pdf)
The system is easy to run, and there are program help files to assist. Tests available run from the extensive (slow) to faster quick checks. This instrument was decommissioned from an active production environment.
Processor Controller Unit:
Model: IPS-6000
Part Number: 1000-0051
Input Voltage: 240 V
Operating System: Windows 2000 Professional
Hard Disk Analyzer:
Model: SRA-FA
An Artisan Technology Group technician and Engineer tested this system and successfully ran many types of scans on spare hard disk platters from our lab that were scratched and scribed. The results of theses tests as well as their interaction with the system's software was well documented. This document was created for download by our technicians:
HDI SRA FA Test Results and Function Document Made by ATG Technicians (pdf)
The system is easy to run, and there are program help files to assist. Tests available run from the extensive (slow) to faster quick checks. This instrument was decommissioned from an active production environment.
Processor Controller Unit:
Model: IPS-6000
Part Number: 1000-0051
Input Voltage: 240 V
Operating System: Windows 2000 Professional
Hard Disk Analyzer:
Model: SRA-FA
This Zygo ZMI-4004 4-Axis VME64x Measurement Board is new from surplus stock.
Part Number: 8020-0500-01
Part Number: 8020-0500-01
This Inficon IC-6000 Vacuum Deposition Controller is used and in excellent condition.
Includes:
• (3) OSC Source S/S Cards
• (1) I/O Card
• (1) DAC Card
Includes:
• (3) OSC Source S/S Cards
• (1) I/O Card
• (1) DAC Card
Included Components:
• DI-340 Controller and Computer
• LG E2242TA Monitor
• Lumetrics 50mm Probe
• Lumetrics Verification Probe w/ F1VS200F2.5 Fiber Optic Microscope and Accessories
• Probe Stand and Accessories
• National Instruments SH68-68-EPM Cable, 2 Meters
• Power Cables for Computer, Controller, and Monitor
TMS 63E-563 Micro-g Vibration Lab Table:
• BreadBoard: 36" x 48" (LxW) CleanTop II
• CleanTop II Thickness: 4"
• Screw Type: 1/4-20, 1" Spacing
• Stabilizers: Gimbal Piston Air Isolators
Configuration:
• Operating System: Windows XP Professional, Ver. 5.01.2600
• Processor: (4) Intel Core i5-2400, 3.10 GHz
• Physical Memory: 3.17 GB RAM
Lumetrics Software and Version:
• OptiGauge Control Center: 6.2.0
National Instruments Software and Versions:
• CVI Run-Time: 8.1.1.361
• NI-DAQmx: 8.7.1f3
• IVI Compliance Package: 3.1
• LabVIEW Run-Time: 7.1
• Measurement & Automation Explorer: 4.4.1.49152
• NI-USI: 1.0.2
• NI-PAL Software: 2.2.0
• NI LabVIEW SignalExpress: 2.5.1
• NI-VISA: 4.2
• NI-VISA Runtime: 4.2
• LabVIEW Run-Time: 8.0.1
• LabVIEW Run-Time: 8.2.1
• LabVIEW Run-Time: 8.5.0
Part Number: 10000-00
View Photo of 50mm probe.
View Photo of verification probe w/ accessories.
View Photo of probe stand and accessories.
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
• DI-340 Controller and Computer
• LG E2242TA Monitor
• Lumetrics 50mm Probe
• Lumetrics Verification Probe w/ F1VS200F2.5 Fiber Optic Microscope and Accessories
• Probe Stand and Accessories
• National Instruments SH68-68-EPM Cable, 2 Meters
• Power Cables for Computer, Controller, and Monitor
TMS 63E-563 Micro-g Vibration Lab Table:
• BreadBoard: 36" x 48" (LxW) CleanTop II
• CleanTop II Thickness: 4"
• Screw Type: 1/4-20, 1" Spacing
• Stabilizers: Gimbal Piston Air Isolators
Configuration:
• Operating System: Windows XP Professional, Ver. 5.01.2600
• Processor: (4) Intel Core i5-2400, 3.10 GHz
• Physical Memory: 3.17 GB RAM
Lumetrics Software and Version:
• OptiGauge Control Center: 6.2.0
National Instruments Software and Versions:
• CVI Run-Time: 8.1.1.361
• NI-DAQmx: 8.7.1f3
• IVI Compliance Package: 3.1
• LabVIEW Run-Time: 7.1
• Measurement & Automation Explorer: 4.4.1.49152
• NI-USI: 1.0.2
• NI-PAL Software: 2.2.0
• NI LabVIEW SignalExpress: 2.5.1
• NI-VISA: 4.2
• NI-VISA Runtime: 4.2
• LabVIEW Run-Time: 8.0.1
• LabVIEW Run-Time: 8.2.1
• LabVIEW Run-Time: 8.5.0
Part Number: 10000-00
View Photo of 50mm probe.
View Photo of verification probe w/ accessories.
View Photo of probe stand and accessories.
Our technicians fully tested this unit. Here are some software screen captures as well as some data scans/tests that were run: Screen Captures (pdf).
This Kevex 952-103 Omicron X-Ray Fluorescence Spectrometer is used and in excellent condition. The unit also includes a monitor for viewing results. This unit was decommissioned from a production facility. A very good effort was made to retain accessories. A 50W source is installed. This unit will need some additional accessories to become complete: PC to Kevex connection cable, etc.
Included Accessories: PC, Mouse Keyboard, CRT Monitor (not shown in photos), Joystick (not shown in photos), X-Ray Warning Lamp, Serial and Power Cabling, Safety Mask and Piping
Photos of Accessories: Photo 1 and Photo 2
PC Hardware and Software Info:
• Pentium II MMX, 333 mHz
• 32 MB RAM, 2 GB HDD
• Ultra Link Model 116D ISA Card
• Windows 98
• Omnicron 2.10
• Omincron 2.20
• Kevex XRF monitor 7.0
Input Voltage: 120 VAC Only
Included Accessories: PC, Mouse Keyboard, CRT Monitor (not shown in photos), Joystick (not shown in photos), X-Ray Warning Lamp, Serial and Power Cabling, Safety Mask and Piping
Photos of Accessories: Photo 1 and Photo 2
PC Hardware and Software Info:
• Pentium II MMX, 333 mHz
• 32 MB RAM, 2 GB HDD
• Ultra Link Model 116D ISA Card
• Windows 98
• Omnicron 2.10
• Omincron 2.20
• Kevex XRF monitor 7.0
Input Voltage: 120 VAC Only
New Arrivals
Artisan Ecotech
