Items/Page
Showing 1-100 of 679 Results
National Instruments SCC-RLY01 1-Channel Relay Module
This unit does not include a terminal block.

Part Number: 187397B-01

View National Instruments SC Signal Conditioning Connector Block.

View National Instruments SCC Analog Input/Output Modules.


National Instruments SCC-AI03 2-Channel Analog Input Module
This unit does not include a terminal block.

Configuration:

• Voltage: 10V

• Frequency: 10 kHz

Part Numbers: 186623E-03, 186623C-03, 186623F-03

View National Instruments SC Signal Conditioning Connector Block.
View National Instruments SCC Digital Input/Output Modules.

Microsemi / Symmetricom / Datum 6502B RF Distribution Module
This Symmetricom / Bancomm / Datum 6502B RF Distribution Module is used and in excellent condition.

Configuration:
• Frequency: .1 - 10 MHz

• Harmonic Distortion: < -40 dB
• Non-Harmonic Signals: < -80 dB
• Voltage: 90-132 or 180-240 VAC

Part Number: 14364-104, 14364-101

National Instruments CB-68LPR 68-Pin Digital and Trigger I/O Terminal Block
It is a low-cost termination accessory with 68 screw terminals for easy connection of field I/O signals to 68-pin DAQ products. The CB-68LPR has a right-angle mounted 68-pin connector.

Dimensions: 7.62 by 16.19 cm (3.00 by 6.36 in.)

Part Number: 184700B-01, 184700C-01, 184700D-01L


Keysight / Agilent E1502A 8-Channel Low-Pass Filter SCP Module
The Agilent E1502A 8-Channel Low-Pass Filter SCP provides eight fixed, 2-pole, low-pass filters with a 3 dB cutoff frequency of 7 Hz. It also provides input over-voltage protection and open transducer detection on each channel.

Agilent E1502A Datasheet (pdf)

Part Numbers: E1413-66512, E1413-63512
Product Family: 5998-01-569-8486, 5998015698486

Keysight / Agilent E1503A 8-Channel Programmable Filter/Gain SCP Module
The Agilent E1503A 8-Channel Programmable Filter and Gain SCP provides eight programmable, 2-pole low-pass filters with cutoff frequency settings of 2, 10, and 100 Hz, as well as a 1.5 kHz "pass-through" mode (filter OFF). The eight programmable input amplifiers provide input voltage ranges of ± 0.25 V, ± 2 V, and ± 16 V. The E1503A SCP also provides input over-voltage protection and open transducer detection on each channel.

Agilent E1503A Datasheet (pdf)
Agilent E1503A Manual (pdf)

Part Number: E1413-66513, E1413-66713, E1413-63513
Product Family: 5998-01-484-1063, 5998014841063

DynamicSignals / Kinetic Systems / Preston 8300 XWB Amplifier
This Kinetic Systems / Preston 8300 XWB Amplifier is used and in excellent condition.

Configuration:
• Gain: 10 Fixed Steps

• Gain Accuracy: ±0.01% ±3 µvolts RTI
• Bandwidth: Switch Selectable 10, 100, 1 kHz, 10 kHz and 100 kHz

Part Number: 61850

Femto DLPCA-200 Universal Low Noise Current Amplifier
This Femto DLPCA-200 Universal Low Noise Current Amplifier is new from surplus stock. This unit ships in the original manufacturer's packaging.

Configuration:
• LEMO Mating Connector
National Instruments SCC-AI04 2-Channel Isolated Analog Input Module
This unit does not include a terminal block.

Configuration:

• Voltage: 5V

• Frequency: 10 KHz

Part Numbers: 186623E-04, 186623C-04, 777459-23

View National Instruments SC Signal Conditioning Connector Block.
View National Instruments SCC Digital Input/Output Modules.

National Instruments SC-2060 8-Channel Optically Isolated Digital Input Module
SC-2060
The SC-2060 has eight optically isolated digital inputs that are routed back to NI DAQ devices. These inputs have independent voltage reference connections and use optocoupler technology to sense digital signals with up to 400 Vrms of common-mode voltage. A digital signal 9 V below the reference is registered as a logical low. A digital signal 3 V below the reference reads as a logical high. The maximum current rating for each input is 20 mA. For applications with higher currents, use a resistor to limit the current.

Part Number: 180925-01, 180925C-01, 180927-01

National Instruments SCC-LP01 Lowpass Filter Module
Configuration:

• Frequency: 25 Hz

Part Numbers: 185200B-01, 777459-07

View National Instruments SC Signal Conditioning Connector Block.
View National Instruments SCC Digital Input/Output Modules.

National Instruments SCC-A10 Voltage Attenuator Module
This unit includes a terminal block.

Part Numbers: 183725C-01, 777459-06

Aerotech BA30-320-S Servo Amplifier
This Aerotech BA30-320-S Servo Amplifier is used and in excellent condition.

Configuration:

• Output Current, Peak: 15 A Cont.
• Operating Bus Voltage: 30 A Peak Servo Amplifier/Power Supply
• Internal Shunt Power Resister: Yes

Part Number: BA30-320-S

National Instruments SCXI-1520 8-Channel Universal Strain/Bridge Module
This National Instruments SCXI-1520 8-Channel Universal Strain/Bridge Module is used and in excellent condition.

Part Numbers: 186338B-01, 186338E-01, 186338D-01, 186338C-01, 186338F-01, 777966-20
Product Family: 6635-01-540-6191, 6635015406191

National Instruments SCC-AO10 1-Channel Isolated Analog Output Module
This unit ships sealed in the manufacturer's box.

Part Number: 188787D-01, 777459-50
National Instruments SC-2345 Signal Conditioning Connector Block
This unit comes with the SCC-PWR02 Power Supply Module installed. The external power supply is not included with this unit.

Power Supply Configuration:
• Universal AC External Supply Required

Part Number: 183687C-02

View National Instruments SCC Analog Input/Output Modules.
View National Instruments SCC Digital Input/Output Modules.

National Instruments SCXI-1120 8-Channel Isolation Amplifier
Part Numbers: 181695-01, 181695E-01, 181695F-01, 181695G-01, 181695H-01, 181695J-01, 776572-20
National Instruments SCXI-1102B 32-Channel Thermocouple Amplifier Module
Part Number: 183087E-02, 183087H-02, 183087K-02L
Product Family: 5998-01-550-9004, 5998015509004
Keysight / Agilent E1508A 8-Channel Fixed Filter SCP Module
The Agilent E1508A 8-Channel x16 Gain & 7 Hz Fixed Filter SCP provides eight fixed, 2-pole, low-pass filters with a 3 dB cutoff frequency of 7 Hz and eight amplifiers with a gain of 16. It also provides input over-voltage protection and open transducer detection on each channel.

Agilent E1508A Datasheet (pdf)
Agilent E1508A Manual (pdf)

Part Number: E1413-66518

Keysight / Agilent E1501A 8-Channel Direct Input SCP Module
The Agilent E1501A Direct Input (>100 kHz BW) Signal Conditioning Plug-on, the most basic of Agilent Technologies' SCPs, provides eight hardwired paths that buffer the input signal. Each path has input over-voltage protection and open transducer detection.

Agilent E1501A Datasheet (pdf)
Agilent E1501A Manual (pdf)

Part Number: E1413-63511

Product Family: 5998-01-507-3533, 5998015073533

Stanford Research SR570 Low-Noise Current Preamplifier
This Stanford Research SR570 Low-Noise Current Preamplifier is used and in excellent condition. Battery is used.
Keysight / Agilent E1501A 8-Channel Direct Input SCP Module
The Agilent E1501A Direct Input (>100 kHz BW) Signal Conditioning Plug-on, the most basic of Agilent Technologies' SCPs, provides eight hardwired paths that buffer the input signal. Each path has input over-voltage protection and open transducer detection.

Agilent E1501A Datasheet (pdf)
Agilent E1501A Manual (pdf)

Part Numbers: E1413-66511, E1413-63511, E1413-63512

Product Family: 5998-01-507-3533, 5998015073533

National Instruments CB-68LP 68-Pin Digital and Trigger I/O Terminal Block
It is a low-cost termination accessory with 68 screw terminals for easy connection of field I/O signals to 68-pin DAQ products. The connector blocks include standoff feet for use on a desktop or mounted in a custom panel. The CB-68LP has a vertical-mounted 68-pin connector.

Dimensions: 14.35 by 10.74 cm (5.65 by 4.23 in.)

Part Number: 183030A-01, 183030B-01, 183030C-01, 183030D-01L

Elmo Motion Control SBA-5/200H Miniature PWM, Full Wave, 3-Phase Servo Amplifier
SBA-5/200H:
• Rated Current: 5
• Max. Rated Voltage: 200
• Hall Sensors

• PWM Switching Frequency: 20 KHz

National Instruments SCXI-1121 4-Channel Isolation Amplifier with Excitation
Part Numbers: 181700-01, 181700E-01, 181700F-01, 181700G-01, 181700H-01, 181700J-01, 776572-21
Product Family: 5998-01-547-3825, 5998015473825
Keysight / Agilent E1513A 8-Channel Fixed Attenuator / Fixed Filter SCP Module
The Agilent E1513A 8-Channel Divide-by-16 Fixed Attenuator and 7 Hz Fixed Filter SCP provides eight fixed low-pass filters with a 3 dB cutoff frequency of 7 Hz and eight divide-by-16 attenuators. It also provides input over-voltage protection.

Agilent E1513A Datasheet (pdf)

Keysight / Agilent E1510A 4-Channel Sample and Hold Input SCP Module
The Agilent E1510A 4-Channel Sample and Hold SCP provides four channels of sample and hold inputs, and four channels of direct inputs for the A/Ds. The sample and hold inputs sample all four channels simultaneously to reduce the skew introduced by scanning.

The SCP circuitry provides a voltage gain of 0.5, 8, 64, or 512 for each channel.

The low-pass filter on each sample and hold channel is a 6th order Bessel active RC filter used to provide alias protection and noise reduction. The filter cutoff frequencies are 1 kHz, 500 Hz, 250 Hz, 100 Hz, and 15 Hz.

Agilent E1510A Datasheet (pdf)
Agilent E1510A Manual (pdf)

National Instruments SC-2060 8-Channel Optically Isolated Digital Input Module
This unit ships sealed in the manufacturer's bag. This unit includes a 0.2 m NB7 SC-205X Cable, Part Number: 180924-02.

SC-2060

The SC-2060 has eight optically isolated digital inputs that are routed back to NI DAQ devices. These inputs have independent voltage reference connections and use optocoupler technology to sense digital signals with up to 400 Vrms of common-mode voltage. A digital signal 9 V below the reference is registered as a logical low. A digital signal 3 V below the reference reads as a logical high. The maximum current rating for each input is 20 mA. For applications with higher currents, use a resistor to limit the current.

Part Number: 180925-01, 180925C-01, 776336-00

National Instruments SCXI-1141 8-Channel Low-Pass Elliptical Filter Module
The SCXI-1141 has elliptic filter response and is recommended for sharp filter roll off.

Part Number: 182628C-01, 182628D-01, 182610D-01, 182610G-01, 182610H-01
Keysight / Agilent E1539A Strain Measurement SCP Module
The Agilent E1422A and its companion products, the E1529A and E1539A, provide a breakthrough in lower cost for automated strain measurements. The E1422A requires E1539A SCPs to control Remote Signal Conditioning Units like the E1529A/B Remote Strain Conditioning Unit.

Agilent E1539A Datasheet (pdf)
Agilent E1539A Manual (pdf)
Agilent E1539A Product Overview (pdf)

Abaco Systems / VMIC VMIVME-3418-202 8-Channel Strain Gauge and RTD Isolated Signal Conditioning VME Board
This GE Fanuc / VMIC VMIVME-3418-202 8-Channel Strain Gauge and RTD Isolated Signal Conditioning VME Board is new from surplus stock.

332-003418-202

• 40 Hz Input Filters
• Constant Current Excitation

National Instruments SCC-SG24 2-Channel Load Cell Input, Full-Bridge, 1.6 kHz Lowpass Module
This unit does not include a terminal block.

Part Numbers: 188154C-01, 777459-37

View National Instruments SC Signal Conditioning Connector Block.

View National Instruments SCC Digital Input/Output Modules.

National Instruments SC-2345 Signal Conditioning Connector Block with Configurable Connectors
This unit ships sealed in the manufacturer's bag. This unit comes with the SCC-PWR01 Power Supply Module installed.

Power Supply Configuration:
• 5 VDC from the DAQ Device or an External Supply

Part Number: 184872C-01, 183687C-01

View National Instruments SCC Analog Input/Output Modules.
View National Instruments SCC Digital Input/Output Modules.

Keysight / Agilent E1512A 8-Channel 25 Hz Fixed Filter SCP Module
The Agilent E1512A 8-Channel 25 Hz Fixed Filter SCP provides eight fixed low-pass filters with a 3 dB cutoff frequency of 25 Hz. It also provides input over-voltage protection and open transducer detection on each channel.

Agilent E1512A Datasheet (pdf)
Agilent E1512A Manual (pdf)

National Instruments SC-2345 Signal Conditioning Connector Block
This unit comes with the SCC-PWR01 Power Supply Module installed.

Power Supply Configuration:

• 5 VDC from the DAQ Device or an External Supply

Part Number: 183687C-01

View National Instruments SCC Analog Input/Output Modules.
View National Instruments SCC Digital Input/Output Modules.

National Instruments SCXI-1102 32-Channel Thermocouple Amplifier Module
Part Number: 183087H-01, 183087L-01, 183087M-01L, 776572-02
Product Family: 5998-01-550-9024, 5998015509024
Aerotech AS32020C 3U Height Brushless Motor Driver
Configuration:
• Control Type: Brushless
• Output Type; PWM
• Peak Current: 20 A

• Fuse Number: 4.5

Frequency Devices VM8PF-8-D828 Programmable VME Filter Board
This Frequency Devices VM8PF Programmable VME Filter Board is used and in excellent condition.

Configuration:

• Channels: 8
• Filter Type: D828L8D80 8-Pole, Constant Delay
• Number of Filters: 8
• Frequency: 100-25.6kHz

Part Numbers: VM8PF, VM8PF-8-D828

National Instruments 184483-01 Blank Panel, 1 9/16
Configuration:
• Height: 1 9/16 in.
• Width: 1 3/16 in.
National Instruments SCC-TC01 Thermocouple Input Module
This unit ships sealed in the manufacturer's bag. This unit does not include a terminal block.

Part Numbers: 184396A-01, 184396B-01, 777459-03


View National Instruments SC Signal Conditioning Connector Block.
View National Instruments SCC Digital Input/Output Modules.

National Instruments SCC-SG24 2-Channel Load Cell Input, Full-Bridge, 1.6 kHz Lowpass Module
This unit ships in the sealed manufacturer's packaging.

Part Numbers: 188154C-01, 777459-37


View National Instruments SC Signal Conditioning Connector Block.
View National Instruments SCC Digital Input/Output Modules.

National Instruments SCC-LP03 Lowpass Filter Module
This unit does not include a terminal block.

Configuration:

• 150 Hz Cutoff Frequency

Part Numbers: 185200B-03

View National Instruments SC Signal Conditioning Connector Block.
View National Instruments SCC Digital Input/Output Modules.

ElectroCraft DC-45L Brush-Type Amplifier
This ElectroCraft DC-45L Brush-Type Amplifier is used and in excellent condition. This unit does not have the built-in heat sink.

Configuration:
• Input: 25-130VAC

• Switching Frequency: 33kHz
• Output Current: 8/16 Amps

ADInstruments ML228 Octal Bridge Amp
This AD Instruments ML228 Octal Bridge Amp is used and in excellent condition.
DL Instruments / Ithaco 1201 Low Noise Voltage Preamplifier
Configuration:
• Option 10 Battery Pack
• Option IEEE 488 Communication
National Instruments SCC-A10 Voltage Attenuator Module
This unit ships in the manufacturer's bag.

Part Numbers: 183725C-01, 777459-06

View National Instruments SC Signal Conditioning Connector Block.

View National Instruments SCC Digital Input/Output Modules.

National Instruments SCXI-1120D 8-Channel Isolation Amplifier
The SCXI-1120D allows the amplifiers to be set by jumpers to be between ±5mV and ±10V.

Part Numbers: 181695G-02, 181695H-02, 181695J-02
Stanford Research SR810 DSP Lock-In Amplifier
This Stanford Research SR810 DSP Lock-In Amplifier is used and in excellent condition.
National Instruments SCXI-1120 8-Channel Isolation Amplifier
SCXI-1120 module and manual included

Part Number: 181695H-01, 181695J-01, 776572-20
National Instruments SCXI-1126 8-Channel Isolated Frequency Input Module
Configuration:
• Maximum Frequency: 128 kHz

• Input Signal: Up to 250 V

Part Numbers: 184642B-01, 184642C-01, 184345D-01, 184345E-01, 776572-26

National Instruments SC-2060 8-Channel Optically Isolated Digital Input Module
SC-2060
The SC-2060 has eight optically isolated digital inputs that are routed back to NI DAQ devices. These inputs have independent voltage reference connections and use optocoupler technology to sense digital signals with up to 400 Vrms of common-mode voltage. A digital signal 9 V below the reference is registered as a logical low. A digital signal 3 V below the reference reads as a logical high. The maximum current rating for each input is 20 mA. For applications with higher currents, use a resistor to limit the current.

Part Number: 180925-01, 180925C-01

National Instruments SCXI-1125 8-Channel Isolation Amplifier
Part Number: 185959B-01, 185959C-01, 185959E-01, 185959F-01, 185959E-02, 185959H-01L, 776572-25
National Instruments SCXI-1520 8-Channel Universal Strain/Bridge Module
This National Instruments SCXI-1520 8-Channel Universal Strain/Bridge Module is new from surplus stock.

Part Number: 186338E-01, 777966-20

Product Family: 6635-01-540-6191, 6635015406191

National Instruments PXIe-7858 / PXIe-7858R R Series Reconfigurable I/O Module
Part Number: 784147-01

Please contact Artisan Technology Group Sales for pricing and availability.
Danaher Motion / Kollmorgen ROL-20012-0000 Line Operated Analog Amplifier
This Danaher Motion / Kollmorgen ROL-20012-0000 Line Operated Analog Amplifier is used and in excellent condition.

ROL-20012-0000 Configuration:
• ROL: Line Operated Analog Amplifier
• Input Voltage: 90-130 VAC
• Continuous Output Current: 12 ADC
• Reserved: Standard

National Instruments SC-2345 Signal Conditioning Connector Block with Configurable Connectors
This unit comes with the SCC-PWR02 Power Supply Module installed. The external power supply is not included with this unit.

Front Panel Configuration:
• (2) BNC Interface Panelettes
• (1) 9-Pin D-Sub

Back Panel Configuration:
• (1) BNC Interface Panelette

Power Supply Configuration:
• Universal AC External Supply Required

Part Number: 184872C-02

View National Instruments SCC Analog Input/Output Modules.
View National Instruments SCC Digital Input/Output Modules.

Agilent / HP / Symmetricom 58502A Broadband Distribution Amplifier
This Agilent / HP / Symmetricom 58502A Broadband Distribution Amplifier is used and in excellent condition.

Configuration:
• Input Frequency Range: .1 MHz to 10 MHz

• Input Amplitude Max: +15dBm
• Input Amplitude Min: +7dBm
• Output: Amplitude: +13dBm, +1dB/-3dB
• Dimensions: 45 mm x 426 mm x 344 mm

Stanford Research SR445 300 MHz Preamplifier
This Stanford Research SR445 300 MHz Preamplifier is used and in excellent condition.

Abaco Systems / VMIC VMIVME-3413-111 32-Channel Signal Conditioning Board
This GE Fanuc / VMIC VMIVME-3413-111 32-Channel Signal Conditioning Board is used and in excellent condition.

VMIVME-3413-111

• Filter Frequency: 10 Hz
• Gain: x1, x10, x100, x1,000 Standard Accuracy
• Input P3, P4 Mating Connector Style: Insulation-Displacement (IDC)

Amplifier Research 25A250AM6 Amplifier
This Amplifier Research 25A250AM6 Amplifier is used and in excellent condition.

Configuration:

• 25 Watts

• 1 to 300 MHz

Dimensions (L x W x H): 19 x 11.3 x 5.2 in

CVI Melles Griot 13AMP005 Wide Bandwidth Amplifier
This CVI Melles Griot 13AMP005 Wide Bandwidth Amplifier is used and in excellent condition.

Configuration:

• Input Current Range: 100 pA to 2 mA

Input Power: 110/220 VAC

Astro-Med / Grass Technologies 7P122G Low Level D.C. Amplifier w/ RSP 107 Regulated Power Supply
These units include cables and connectors.

View Photo of cables and connectors.

National Instruments SC-2345 Signal Conditioning Connector Block with Configurable Connectors
This unit includes a 9-Pin Female D-Sub Connector Panel Kit, Part Number: 184738-03. This unit comes with the SCC-PWR01 Power Supply Module installed.

Power Supply Configuration:
• 5 VDC from the DAQ Device or an External Supply

Part Number: 186723B-01

View National Instruments SCC Analog Input/Output Modules.
View National Instruments SCC Digital Input/Output Modules.

Vaisala UPP210 Receiver Processor Unit
This Vaisala UPP210 Receiver Processor Unit is used and in excellent condition.
Product Family: 5895-01-392-2191, 5895013922191
EADS / Trig-Tek 801B Compressor
This EADS / Trig-TEK 801B Compressor is used and in excellent condition.

Configuration:
• Front Panel DC Offset Switch

Part Number: 801B ADD 1
National Instruments SCC-RTD01 2-Channel RTD Input Module
This unit does not include a terminal block.

Part Number: 186760C-01, 777459-18

View National Instruments SC Signal Conditioning Connector Block.

View National Instruments SCC Digital Input/Output Modules.

Kollmorgen VRDM Servo Amplifier
This unit is also known as the Servotronix VRDM Servo Amplifier.

Part Numbers: PRD-0051AMPF-Y0, PRD-O051AMPE-XO, PRD-0051AMPE-XO, 50045607, 50045707, PRD-0051AMPA-Y0, PRD-0051AMPA-X0, 50045603

National Instruments PXI-5610 2.7 GHz Upconverter
This National Instruments PXI-5610 2.7 GHz Upconverter is used and in excellent condition.

Part Number: 189590C-01, 189718E-01
Princeton Applied Research / EG&G 162 Boxcar Averager
This Princeton Applied Research / EG&G Model 162 Boxcar Averager is used and in excellent condition.

Configuration:
• Digital Option Installed

• (2) Model 165 Gated Integrator Modules

Input Power: 115 / 230 VAC

National Instruments SC-2345 Signal Conditioning Connector Block with Configurable Connectors
This unit comes with the SCC-PWR02 Power Supply Module installed. The external power supply is not included with this unit.

Configuration:

• (6) Banana Jack Interface Panelettes
• (1) K-Type Minithermocouple Interface Panelette
• (1) J-Type Minithermocouple Interface Panelette
• (1) BNC Interface Panelette

Power Supply Configuration:
• Universal AC External Supply Required

Part Number: 184872C-02

View National Instruments SCC Analog Input/Output Modules.
View National Instruments SCC Digital Input/Output Modules.

National Instruments SC-2345 Signal Conditioning Connector Block with Configurable Connectors
This unit comes with the SCC-PWR02 Power Supply Module installed. The external power supply is not included with this unit.

Front Panel Configuration:
• (2) BNC Interface Panelettes
• (1) Banana Jack Interface Panelette
• (1) 9-Pin D-Sub

Back Panel Configuration:
• (7) Banana Jack Interface Panelettes
• (2) BNC Interface Panelettes

Power Supply Configuration:
• Universal AC External Supply Required

Part Number: 184872C-02

View National Instruments SCC Analog Input/Output Modules.
View National Instruments SCC Digital Input/Output Modules.

National Instruments SC-2345 Signal Conditioning Connector Block with Configurable Connectors
This unit comes with the SCC-PWR02 Power Supply Module installed. The external power supply is not included with this unit.

Configuration:

• Includes Rack Mount Kit

Power Supply Configuration:
• Universal AC External Supply Required

Part Number: 184872C-02

View National Instruments SCC Analog Input/Output Modules.
View National Instruments SCC Digital Input/Output Modules.

National Instruments SCC-SG24 2-Channel Load Cell Input, Full-Bridge, 1.6 kHz Lowpass Module
This unit ships in the sealed manufacturer's static bag.

Part Numbers: 188154C-01, 777459-37


View National Instruments SC Signal Conditioning Connector Block.
View National Instruments SCC Digital Input/Output Modules.

National Instruments SCC-TC01 Thermocouple Input Module
This unit does not include a terminal block.

Part Numbers: 184396A-01, 184396B-01, 777459-03


View National Instruments SC Signal Conditioning Connector Block.
View National Instruments SCC Digital Input/Output Modules.

Keithley 604 Differential Electrometer Amplifier
This Keithley 604 Differential Electrometer Amplifier is used and in excellent condition.
National Instruments SCC-LP03 Lowpass Filter Module
This unit ships sealed in the manufacturer's static.

Configuration:

• 150 Hz Cutoff Frequency

Part Numbers: 185200B-03

View National Instruments SC Signal Conditioning Connector Block.
View National Instruments SCC Digital Input/Output Modules.

Tektronix VX4780 Signal Conditioner Module
This Tektronix VX4780 Signal Conditioner Module is used and in excellent condition.
Krohn-Hite 3945 3Hz to 25.6MHz High-Pass/Low-Pass Butterworth/Bessel Programmable Filter
This Krohn-Hite 3945 3Hz to 25.6MHz High-Pass/Low-Pass Butterworth/Bessel Programmable Filter is used and in excellent condition.
National Instruments SC-2345 Signal Conditioning Carrier with PCB
Part Number: 186723B-01, 186723B-02
PCB Part Number: 186474B-01


View Photo of PCB.

View National Instruments SCC Analog Input/Output Modules.
View National Instruments SCC Digital Input/Output Modules.

Thorlabs / Exfo / Burleigh DA-100 Detector Amplifier
This Burleigh DA-100 is used and in excellent condition.
Keithley 427 Current Amplifier
This Keithley 427 Current Amplifier is used and in excellent condition.
National Instruments SCC-A10 Voltage Attenuator Module
This unit does not include a terminal block.

Part Numbers: 183725C-01, 777459-06

View National Instruments SC Signal Conditioning Connector Block.

View National Instruments SCC Digital Input/Output Modules.

ElectroCraft DC-45L Brush-Type Amplifier with Heat Sink
This ElectroCraft DC-45L Brush-Type Amplifier is used and in excellent condition.

Configuration:
• Input: 25-130VAC
• Switching Frequency: 33kHz

• Output Current: 8/16 Amps

National Instruments SCC-AI03 2-Channel Analog Input Module
This unit does not include the plastic housing or terminal block.

Configuration:

• Voltage: 10V

• Frequency: 10 kHz

Part Numbers: 186623E-03, 186623C-03, 186623F-03

View National Instruments SC Signal Conditioning Connector Block.
View National Instruments SCC Digital Input/Output Modules.

Keysight / Agilent 81578A Optical Attenuator
This Agilent / HP 81578A Optical Attenuator is used and in excellent condition.

Configuration:
• Insertion Loss: < 1.4 dB

• Frequency: 700 - 1400 nm
• Attenuation Range: 0 - 60 dB
• Max Input Power: + 27 dB
• Fiber Type: 62.5 / 125 μm MMF
• Optical Interface: PC

Option 062 Typical IL's:
• 1.0 dB (NA = 0.1)
• 1.3 dB (NA = 0.2)
• At Most 2.0 dB (NA = 0.2)
• 3.0 dB (NA = 0.27)

This instrument includes the standard Agilent optical interface (View Photo). The Agilent 81000xI Series optical interface connectors are sold separately. They are available for purchase from our website here: (Item #50516).

Showing 1-100 of 679 Results
Contact Us
Fax:

(240) 376-1381