Vincent / UniBlitz D122 Shutter Driver
  • Vincent_UniBlitz_D122_View1_2018529154333
  • Vincent_UniBlitz_D122_View2_2018529154333
  • Vincent_UniBlitz_D122_View3_2018529154333
  • Vincent_UniBlitz_D122_View4_2018529154333
  • Vincent_UniBlitz_D122_View5_2018529154333

Vincent / UniBlitz D122 Shutter Driver

This unit ships with a Shutter cable and a RS-232 cable.

View Photo of included cables.

Have a quote from somewhere else? Click Here
Stock # 58020-5
Quick Quote
Sell Yours
Repair Quote
  • More Info
  • Tech Specs
  • Additional Photos
  • Datasheets / Manuals 
  • View It Live Request 
Contact Us
Vincent / UniBlitz D122 and T132 Shutter Drivers

  • Patented Driver Design
  • Automatic Voltage Switching
  • Selectable Pulse Energy Switch
  • Controllable Via RS232 Interface
  • Normally Open or Normally Closed Operation
  • Operate Any UniBlitz Shutter to it's Maximum Frequency


The UniBlitz D122 and T132 are capable of controlling all shutters in the UniBlitz line. The T132 incorporates two precise timers to control shutter exposure and delay interval. Each timer ranges from .1ms to 9999sec. Four digit push-wheel switches provide exceptional resolution for use in a multitude of shutter applications, ranging from photography to holography. The D122 drives the shutter while relying on the users input signal to determine exposure and frequency.

One feature of the T132 is the PRE or POST exposure delay. The PRE/POST toggle switch allows the user to actuate the shutter immediately upon receipt of a trigger signal or delay the EXPOSURE for a predetermined period. The period of the DELAY interval is determined from the front panel DELAY TIME SELECT. The DELAY signal is provided to an output (BNC connector) for the DELAY interval. In addition to the PRE/POST DELAY, the T132 can re-trigger itself continuously to provide a low-level chopper control. In the CONT. mode the DELAY interval control acts as the recycle interval to determine the exposure frequency. By using external control capability and this mode, exposure bursts can be controlled using the T132 EXPOSURE and DELAY timers. Set the T132 into continuous mode and trigger the system to begin cycling. By monitoring the pulse output the precise cutoff point can be determined and the unit can be reset without interrupting the exposure cycle.

One feature of the D122 is the selection of interrupt mode. With the mode switch in the A position, the unit will disable itself upon a AC line failure. When power is restored, the unit will remain disabled until reset. In the B position the unit will become disabled when a DC voltage level is removed from the interrupt input. When the input is restored, the unit will remain disabled until reset. The STD mode will bypass the interrupt capability. This mode selection makes the D122 more versatile for applications where the shutter must not reopen until acted upon by the user.

The patented driver design of the D122 and T132 allows any UniBlitz shutter including VS35) to be operated to its maximum frequency as specified in the shutter data sheets. Other features of the D122 and T132 include, automatic switching for 115VAC or 230VAC operation, controllable via RS232 interface, normally open or normally closed operation, selectable pulse energy switch for VS35 operation, convenient output for shutters equipped with electronic synchronization switch, and an external regulated +5VDC supply (T132 only - +8VDC unregulated D122).

Important Notice: Please note that any additional items included with this equipment such as accessories, manuals, cables, calibration data, software, etc. are specifically listed in the above stock item description and/or displayed in the photos of the equipment. Please contact one of our Customer Support Specialists if you have any questions about what is included with this equipment or if you require any additional information.

Contact Us


Contact Us

Item Images

Click a thumbnail to view larger image:

Vincent / UniBlitz D122 and T132 Shutter DriversVincent / UniBlitz D122 and T132 Shutter DriversVincent / UniBlitz D122 and T132 Shutter Drivers
Vincent / UniBlitz D122 and T132 Shutter Drivers

Contact Us

View It Live

View equipment LIVE - Before you buy!

InstraView™ Equipment Inspection

Buying used equipment doesn't always have to be a shot in the dark. We know there are plenty of differences when it comes to used equipment and quite often, choosing between different pieces is difficult, especially when the equipment is not sitting right in front of you.

Well, what if you were able to see a piece of equipment before you purchased it? Not just a picture from the manufacturer's website, but the actual piece of equipment you would receive.
With InstraView™, we move you one step closer to inspecting the equipment you're interested in without having to wait for the equipment to show up at your door.

InstraView™ works in your web browser and allows you to view the actual piece of equipment you're interested in before purchasing. You can zoom in close to see the labels with the serial number or zoom out to see the overall condition of the equipment.

It's like having the store come to you!

InstraView Request Form

To get started:

  1.   Fill in the request form below
  2.   We'll send you an email letting you know exactly when your piece of equipment will be available for viewing

Item to Inspect: 58020-5 - Vincent / UniBlitz D122 Shutter Driver

All you need is a web browser (ie. Microsoft Internet Explorer or Netscape) and Sun's Java Runtime Environment installed. If you need to install the Sun Java Runtime, you may download the latest Java SE Runtime Environment (JRE)