DynamicSignals / Kinetic Systems V200-AA11 16-Channel 16-Bit Sigma-Delta ADC

DynamicSignals / Kinetic Systems V200-AA11 16-Channel 16-Bit Sigma-Delta ADC

This Kinetic Systems V200 16-Channel 16-Bit Sigma-Delta ADC is used and in excellent condition. This is the base card option.

Have a quote from somewhere else? Click Here
Stock # 63512-1
Quick Quote
Sell Yours
Repair Quote
  • More Info
  • Tech Specs
  • Additional Photos
  • Datasheets / Manuals 
  • View It Live Request 
Contact Us
DynamicSignals / Kinetic Systems V200 16 or 32-Channel 16-Bit Sigma-Delta ADC

  • 16 or 32 Channels
  • 16-Bit Resolution
  • Analog-to-Digital Conversion
  • Sample Rates Up to 200k/s Per Channel


The Kinetic Systems V200 16 or 32-Channel 16-Bit Sigma-Delta ADC is a single-width, C-size, register-based, VXIbus module that provides 16 or 32-channels of 16-bit resolution analog-to-digital conversion at sample rates up to 200 ksamples/s per channel. The sigma-delta architecture provides inherent filtering and synchronous sampling without the need for sample/hold amplifiers or sophisticated analog filters. A simple, 3-pole pre-filter assures no frequency aliasing. The module is divided into two channel groups, allowing one half of the channels to be operated at one clock rate, while the other half are operated at another clock rate. The groups can also be combined, operating the entire module at one clock rate.

Each channel has independently programmable input spans from ±10 mV to ±10 V provided by an instrumentation amplifier front end. AC/DC coupling can also be programmed on a channel-by-channel basis. Channel calibration and self-test are performed automatically on command by the embedded DSPs. These DSPs also allow programmable level and slope limit checking.

Clocking for the ADCs may be provided by an internal programmable clock, or externally via the VXI trigger lines or via the front panel Clock In connector. A phase-locked loop (PLL) generates the required 64-times oversampling clock needed by the ADCs for these external clock sources. The entire module must be operated at the same clock rate to use the 1X PLL clock.

The V200 provides an onboard ping-pong interface to the VXIbus. The module is also available with a multibuffer memory or a communication port interface. The multibuffer permits configuration for continuous operation or for transient capture. In transient capture mode, the number of pre- and post-trigger samples may be programmed, with the trigger source being selectable from either on-board limit checking, the VXIbus trigger lines, or the front panel Trigger In connector. The communication interface option can move the data as it is acquired to an external TI TMS320, ‘C40 or ‘C44 Digital Signal Processor (DSP). This interface includes two communication ports, one for each V200 channel group.

Product Family: V200, V 200, V-200

Important Notice: Please note that any additional items included with this equipment such as accessories, manuals, cables, calibration data, software, etc. are specifically listed in the above stock item description and/or displayed in the photos of the equipment. Please contact one of our Customer Support Specialists if you have any questions about what is included with this equipment or if you require any additional information.

Contact Us


Contact Us

Item Images

Click a thumbnail to view larger image:

Kinetic Systems V200 16 or 32-Channel 16-Bit Sigma-Delta ADC

Contact Us

View It Live

View equipment LIVE - Before you buy!

InstraView™ Equipment Inspection

Buying used equipment doesn't always have to be a shot in the dark. We know there are plenty of differences when it comes to used equipment and quite often, choosing between different pieces is difficult, especially when the equipment is not sitting right in front of you.

Well, what if you were able to see a piece of equipment before you purchased it? Not just a picture from the manufacturer's website, but the actual piece of equipment you would receive.
With InstraView™, we move you one step closer to inspecting the equipment you're interested in without having to wait for the equipment to show up at your door.

InstraView™ works in your web browser and allows you to view the actual piece of equipment you're interested in before purchasing. You can zoom in close to see the labels with the serial number or zoom out to see the overall condition of the equipment.

It's like having the store come to you!

InstraView Request Form

To get started:

  1.   Fill in the request form below
  2.   We'll send you an email letting you know exactly when your piece of equipment will be available for viewing

Item to Inspect: 63512-1 - DynamicSignals / Kinetic Systems V200-AA11 16-Channel 16-Bit Sigma-Delta ADC

All you need is a web browser (ie. Microsoft Internet Explorer or Netscape) and Sun's Java Runtime Environment installed. If you need to install the Sun Java Runtime, you may download the latest Java SE Runtime Environment (JRE) http://www.oracle.com/technetwork/java/javase/downloads/index.html