RadiSys EPC-1 Series CPU and Disk Modules
  • radisys_epc_1p_view2
  • radisys_epc_1ms_view2

RadiSys EPC-1 Series CPU and Disk Modules

Features

  • Rugged, Modular PC-Compatible Computers
  • Versatile and Compact
  • Data-Acquisition and Real-Time Multi-Processor Systems

View our selection of these items below.


Have a quote from somewhere else? Click Here




Contact Us
Share:



This RadiSys EPC-1P Embedded Computer Module is used and in excellent condition.

Configuration:

• 20 MHz Intel A80386DX-20 Processor
• 20 MHz Math Co-Processor
• 4 MB Memory Installed
• Reset Button, RUN, SYSFAIL, and TEST LEDs
• Floppy Disk Interface
• LPT 1, COM 1, COM 2 Connectors
• Keyboard and Monitor Connectors

Part Number (Top Board): EPC-1/2C (61-0016-06)
Part Number (Bottom Board): EPC-1/E (51-0019-07)




Stock # 68006-9




This RadiSys EPC-1MS Mass Storage Module is used and in excellent condition.

Configuration:

• 42 MB Hard Drive
• Floppy Drive Installed




Stock # 55570-7




This RadiSys EPC-1P Embedded Computer Module is used and in excellent condition.

Configuration:

• 16 MHz Intel A80386DX-16 Processor
• 1 MB Memory Installed
• Reset Button, RUN, SYSFAIL, and TEST LEDs
• Floppy Disk Interface
• LPT 1, COM 1, COM 2 Connectors
• Keyboard and Monitor Connectors

Part Number (Top Board): EPC1I020
Part Number (Bottom Board): EPC11601




Stock # 55570-8



  • Description
  • Tech Specs
  • Datasheets / Manuals 
Contact Us
Share:

Description

RadiSys EPC-1AM
The RadiSys EPC-1AM adapter module is designed to accept 8-bit PC/AT short cards (up to 5.75 inches long). The EPC-1AM has three components: a front panel, a circuit board, and a replacement SCSI disk cable. The circuit board has an edge connector and a sliding bracket which allow a PC/AT short card to be mounted upside down with its panel connector facing the front of the VMEbus card cage. On the back of the adapter module circuit board is a 96-pin female connector which plugs into a matching pin group on the outer board of the EPC-1P CPU module.

Because it typically resides between the CPU and disk modules in an EPC-1 system, the adapter module circuit board has two rectangular holes through which the SCSI and floppy drive cables may pass. Diskless network nodes consist of the adapter and CPU modules, along with the appropriate networking card and software.

RadiSys EPC-1GE
The RadiSys EPC-1GE processor module comes configured for use with a GE Fanuc Series 90-70 PLC acting as slot-1 controller. The EPC-1GE is used in conjunction with the EPC-1MS mass storage module and an EGA monitor. All the switches necessary for modifying this configuration are in a single DIP switch block on the top board of the processor module.

RadiSys EPC-1SE
The RadiSys EPC-1SE SCSI extension module allows you to use an external SCSI device with your EPC-1. The EPC-1SE consists of a single-slot front panel with a standard D-subminiature SCSI connector (with bail fasteners) on a 50-pin SCSI cable. The SCSI cable has two 50-pin female connectors: one attaches to the hard disk on the EPC-1MS mass storage module; the other attaches to connector pins on the EPC-1P CPU module.

The EPC-1SE is designed to reside in the slot immediately to the right of the EPC-1MS (or immediately to the right of the EPC-1P if no mass storage module is present).



Product Family: EPC-1AM, EPC-1GE, EPC-1MS, EPC-1P, EPC-1SE, EPC 1AM, EPC 1GE, EPC 1MS, EPC 1P, EPC 1SE, EPC1AM, EPC1GE, EPC1MS, EPC1P, EPC1SE, 61-0016-06, 61-0019-07, EPC-1/1E, EPC-1/2C, 458710-005, EPC1I020
Contact Us
Share:

Specifications

Contact Us
Share:

Resources

Manuals, Datasheets, Drivers, Links

RadiSys EPC-1AM Manual (pdf) 
RadiSys EPC-1GE Manual (pdf) 
RadiSys EPC-1SE Manual (pdf) 
Link to RadiSys Website