Abaco Systems / VMIC VMIVME-2210-100 64-Channel Momentary Relay Board with Built-in-Test
  • GE_Fanuc_VMIC_VMIVME_2210_100_View1_201533114340
  • GE_Fanuc_VMIC_VMIVME_2210_100_View2_201533114340
  • GE_Fanuc_VMIC_VMIVME_2210_100_View3_201533114340

Abaco Systems / VMIC VMIVME-2210-100 64-Channel Momentary Relay Board with Built-in-Test



This GE Fanuc / VMIC VMIVME-2210-100 64-Channel Momentary Relay Board with Built-in-Test is new from surplus stock.

VMIVME-2210-100

• Nonlatching Relays
• 64-Channel

Part Number: 332-012210-100 B




Have a quote from somewhere else? Click Here
Stock # 72080-3
Quick Quote
Sell Yours
Repair Quote
  • More Info
  • Tech Specs
  • Additional Photos
  • Datasheets / Manuals 
  • View It Live Request 
Contact Us
Share:
Abaco Systems / VMIC VMIVME-2210 64-Channel Latching or Momentary Relay Board with Built-in-Test

Features
  • Latching Contacts Hold Their State with Power Off
  • Available in Latching and Nonlatching Versions
  • 1 Form C Contacts (SPDT) with 96-Conductor Cable
  • 1 Form A Contacts (SPST) with 64-Conductor Cable
  • 8-, 16-, or 32-Bit Data Transfers
  • Supports Real Time and Off-Line Fault Detection and Isolation
  • 2.0 A Current Rating
  • Protection from Relays Changing During Power Up/Down

Description

The GE Fanuc / VMIC VMIVME-2210 provides 64 One Form C (SPDT) contacts to the user via two 96-pin DIN connectors. These relays are the magnetic latching type which means that, once a contact is set it will remain set (even if power is removed from the relay) until it is reset. All three contact points are brought out via the connector. They are the N.O. (Normally Open), N.C. (Normally Closed), and the Common contact points. The N.O. and the Common can be used to create One Form A contacts while the N.C. and common can be used as One Form B contacts. The N.O. contacts are on Row A of the connectors and the common contacts are on Row C of the connector as shown in Figure 1. This arrangement permits 64-conductor cables to be used for Form A switches.

The VMIVME-2210 is populated with double pole relays, but only one pole is brought out to the user. The other pole is used by the Built-in-Test (BIT) logic. The state of the controlling Data Registers or the N.C. poles is read during read accesses of the board. The Control Registers are located at the same address as the relays. This allows the user to monitor both the state of the user contacts and the Control Registers. Because the read pole and the user’s pole are controlled by the same coil, BIT can monitor the user’s contacts via the N.C. contacts of the second pole.

The N.C. contacts provide a logic one from the contacts for a logic one written to the Data Register. This provides positive data feedback from the contact BIT logic. When a logic one is written to the Control Register, it activates the relay which causes the N.O. contacts to close and the N.C. contacts to open. When the contact BIT logic is read, a logic one is returned.

The Control Data Registers are also monitored because the relays take a long time (7 ms maximum) to change their contacts. VMEbus accesses of the board can execute so quickly the relays seem to be faulty resulting in erroneous conclusions. To prevent this the user can check the Data Register’s state, instead of waiting for the relay’s contacts to close.

This board uses latching relays which hold their state when power is removed. This means that closed contacts stay closed until commanded to open.


Product Family: VMIVME 2210, VMIVME2210


Important Notice: Please note that any additional items included with this equipment such as accessories, manuals, cables, calibration data, software, etc. are specifically listed in the above stock item description and/or displayed in the photos of the equipment. Please contact one of our Customer Support Specialists if you have any questions about what is included with this equipment or if you require any additional information.


Contact Us
Share:

Specifications

Contact Us
Share:

Item Images

Click a thumbnail to view larger image:

GE Fanuc / VMIC VMIVME-2210 64-Channel Latching or Momentary Relay Board with Built-in-Test


Contact Us
Share:

View It Live

View equipment LIVE - Before you buy!

InstraView™ Equipment Inspection



Buying used equipment doesn't always have to be a shot in the dark. We know there are plenty of differences when it comes to used equipment and quite often, choosing between different pieces is difficult, especially when the equipment is not sitting right in front of you.

Well, what if you were able to see a piece of equipment before you purchased it? Not just a picture from the manufacturer's website, but the actual piece of equipment you would receive.
With InstraView™, we move you one step closer to inspecting the equipment you're interested in without having to wait for the equipment to show up at your door.

InstraView™ works in your web browser and allows you to view the actual piece of equipment you're interested in before purchasing. You can zoom in close to see the labels with the serial number or zoom out to see the overall condition of the equipment.

It's like having the store come to you!


InstraView Request Form

To get started:

  1.   Fill in the request form below
  2.   We'll send you an email letting you know exactly when your piece of equipment will be available for viewing

Name:
Email:
Item to Inspect: 72080-3 - Abaco Systems / VMIC VMIVME-2210-100 64-Channel Momentary Relay Board with Built-in-Test


All you need is a web browser (ie. Microsoft Internet Explorer or Netscape) and Sun's Java Runtime Environment installed. If you need to install the Sun Java Runtime, you may download the latest Java SE Runtime Environment (JRE) http://www.oracle.com/technetwork/java/javase/downloads/index.html