Measurement Computing PCI-DDA04/12 Analog Output Board

Measurement Computing PCI-DDA04/12 Analog Output Board



This Measurement Computing PCI-DDA04/12 Analog Output Board is used and in excellent condition.



Have a quote from somewhere else? Click Here
Stock # 75416-1
Quick Quote
Sell Yours
Repair Quote
  • More Info
  • Tech Specs
  • Additional Photos
  • Datasheets / Manuals 
  • View It Live Request 
Contact Us
Share:
Measurement Computing PCI-DDA04/12 Analog Output Board

Features
  • Provides Four Channels of 12-Bit Analog Output and 48 Bits of Digital I/O
  • D/A Converters Independently Configurable for Bipolar or Unipolar
  • Software Selectable Settings

Description

The Measurement Computing PCI-DDA04/12 provides four channels of 12-bit analog output and 48 bits of digital I/O.

The D/A converters can be independently configured for either Bipolar or Unipolar. Bipolar ranges are ±10V, ±5V, and ±2.5V. Unipolar ranges are 0 to 10V, 0 to 5V, and 0 to 2.5V. The outputs may be updated individually or simultaneously. The range settings are software-selectable.

The digital I/O ports are configured as two 82C55 mode 0 emulations. Each group is divided into three 8-bit ports: Port A, Port B, and Port C. Port C can be split into two four-bit ports: Port C-HI and Port C-LO. Each of these ports may be individually programmed as input or output. The digital outputs are capable of sinking 64mA and sourcing 15mA utilizing standard "S" logic.

The PCI interface uses the PLX 9052 chip, which is a slave-only device. The PCI interface for the analog output is configured in a 16-bit, multiplexed address/data bus, I/O access mode. The PCI interface for the digital I/O is configured in an 8-bit, multiplexed address/data bus, I/O access mode to be register-compatible with the PCI-DIO48H and PCI-DIO96H boards.

The PCI-DDA04/12 board is completely plug-and-play, with no jumpers or switches to set. All board addresses are set by the board's plug-and-play software. Board configuration is controlled by your system's BIOS.


Important Notice: Please note that any additional items included with this equipment such as accessories, manuals, cables, calibration data, software, etc. are specifically listed in the above stock item description and/or displayed in the photos of the equipment. Please contact one of our Customer Support Specialists if you have any questions about what is included with this equipment or if you require any additional information.


Contact Us
Share:

Specifications

Power Consumption
+5V Operating1.5A typical, 2.4A max
+12V12mA typical, 24mA max
-12V8mA typical, 12mA max
Analog Output
D/A Converter TypeAD7837B
Resolution12 bits
Number of Channels4
Output Range±10V, ±5V, ±2.5V, 0 to 10V, 0 to 5V, 0 to 2.5V, pinout
Each channel independently programmable
Data TransferProgrammed I/O
Offset Error Pinout (Calibrated)±(300µV + 1/4 LSB)
Gain Error (Calibrated)±(300µV + 1/4 LSB)
Differential Nonlinearity±1 LSB max
Integral Nonlinearity±1 LSB max
Monotonicity12 bits
D/A Gain Drift±2 ppm/°C
D/A Offset Drift±5µV/°C
ThroughputPC dependent
Settling Time (20V step to ±1/2 LSB)6µs typical, 10µs max
Slew Rate5V/µs
Current Drive±5mA
Output Short-Circuit Duration25mA indefinite
Output CouplingDC
Output Impedence0.1 Ohms max
Miscellaneous• Double buffered output latches
• Update DACs individually or simultaneously (software selectable)
• Power up and reset, all DACs cleared to 0 volts, ±210mV
Digital I/O
Digital Type (Main Connector)82C55 mode 0 emulation
Output: 74S244
Input: 74L373
Configuration4 banks of 8, 4 banks of 4, programmable by bank as input or output
Number of Channels48 I/O
Output High2.4V min @ -15mA
Output Low0.5V max @ 64mA
Input High2.0V min, 7V absolute max
Input Low0.8V max, -0.5V absolute min
Power-Up/Reset StateInput mode (high impedance)
Environmental
Operating Temperature Range0 to 70°C
Storage Temperature Range-40 to 100°C
Humidity0 to 90% non-condensing
Main Connector and Pinout
Connector Type100-pin, high density connector
Compatible CablesC100FF-x pinout-unshielded ribbon cable (x = length in feet)
Compatible Accessory Products with the C100FF-x CableCIO-TERM100; CIO-MINI50 (two required)


Contact Us
Share:

Item Images

Click a thumbnail to view larger image:

Measurement Computing PCI-DDA04/12 Analog Output BoardMeasurement Computing PCI-DDA04/12 Analog Output BoardMeasurement Computing PCI-DDA04/12 Analog Output Board
Measurement Computing PCI-DDA04/12 Analog Output Board


Contact Us
Share:

View It Live

View equipment LIVE - Before you buy!

InstraView™ Equipment Inspection



Buying used equipment doesn't always have to be a shot in the dark. We know there are plenty of differences when it comes to used equipment and quite often, choosing between different pieces is difficult, especially when the equipment is not sitting right in front of you.

Well, what if you were able to see a piece of equipment before you purchased it? Not just a picture from the manufacturer's website, but the actual piece of equipment you would receive.
With InstraView™, we move you one step closer to inspecting the equipment you're interested in without having to wait for the equipment to show up at your door.

InstraView™ works in your web browser and allows you to view the actual piece of equipment you're interested in before purchasing. You can zoom in close to see the labels with the serial number or zoom out to see the overall condition of the equipment.

It's like having the store come to you!


InstraView Request Form

To get started:

  1.   Fill in the request form below
  2.   We'll send you an email letting you know exactly when your piece of equipment will be available for viewing

Name:
Email:
Item to Inspect: 75416-1 - Measurement Computing PCI-DDA04/12 Analog Output Board


All you need is a web browser (ie. Microsoft Internet Explorer or Netscape) and Sun's Java Runtime Environment installed. If you need to install the Sun Java Runtime, you may download the latest Java SE Runtime Environment (JRE) http://www.oracle.com/technetwork/java/javase/downloads/index.html