Items/Page
28 / 28 Results
Configuration:
• AC Power Input: 90-120 VAC Single Phase, 50/60 Hz; 500 VA Max. at 7.9 amp Setting

• Motor Current: 0 - 7.9 amps, 0.1 amp Increments
• Fold Back: Automatic
• Bus Voltage: 160 VDC Nominal

This unit is the SmartStep-23 with the standard back panel mounts.

Configuration:

• RS485 Communication Option Installed
• Step Sizes: 36,000 steps/rev
• Input Voltage: 90-120 VAC Single Phase, 50/60 Hz, 250 VA Max at 3.0 Amps
• Output Current: 0-3 Amps, 0.1 Amp Increments

Configuration:

• RS232 Communication (Standard)
• Step Sizes: 36,000 steps/rev

• Input Voltage: 90-120 VAC Single Phase, 50/60 Hz, 500 VA Max at 7.9 Amps
• Output Current: 0-7.9 Amps, 0.1 Amp Increments

This unit is the SmartStep-23 with the standard back panel mounts.

Configuration:

• RS232 Communication (Standard)

• Step Sizes: 36,000 steps/rev
• Input Voltage: 90-120 VAC Single Phase, 50/60 Hz, 250 VA Max at 3.0 Amps
• Output Current: 0-3 Amps, 0.1 Amp Increments

This unit is the SmartStep-23 with the Minimal Depth (MD) option.

Configuration:

• Step Sizes: 36,000 steps/rev

• Input Voltage: 90-120 VAC Single Phase, 50/60 Hz, 250 VA Max at 3.0 Amps
• Output Current: 0-3 Amps, 0.1 Amp Increments

Options:

• MD: Minimal Depth; Mounts on side panel rather than back panel.

This unit operates on a power supply of 110V AC.

This unit contains:
Smartdrive V6.20
Keypad V2.80
FPGA V7.1
Cable with wires has been cut close to the motor body (see photo). Not connectorized.

S21 Motor:

• Holding Torque: 65 oz-in (0.46 N-m)
• Recommended Current/Phase Series (Parallel): 1.2 (2.4)

Part Number: 801-121

Configuration:
• AC Power Input: 90-120 VAC Single Phase, 50/60 Hz; 500 VA Max. at 7.9 amp Setting

• Motor Current: 0 - 7.9 amps, 0.1 amp Increments
• Fold Back: Automatic
• Bus Voltage: 160 VDC Nominal
• Option: Low Drive Resolution

Configuration:
• Holding Torque: 65 oz-in (0.46 N-m)

Part Number: 801-121
This units bios will need to be replaced for it to be fully functional. Please contact the manufacturer for pricing and availability.
This unit is the SmartStep Standard with the Minimal Depth (MD) option.

Configuration:

• Step Sizes: 36,000 steps/rev
• Input Voltage: 90-120 VAC Single Phase, 50/60 Hz, 500 VA Max at 7.9 Amps
• Output Current: 0-7.9 Amps, 0.1 Amp Increments

Options:

• MD: Minimal Depth; Mounts on side panel rather than back panel.

Configuration:
• Standard 6K Memory
• 2-Axis Control
• 90 - 240 VAC, 50/60 Hz, Single Phase
• Power Input: 2300VA at 115 VAC, 4600VA at 230 VAC

• Front Panel Not Included
This Danaher Motion / IDC 961-NP Single Axis Indexer is used and in excellent condition.

961-NP:

• 961: 1 Axis Unit
• NP: No Front Panel

B8962 Configuration:
• Standard 6K Memory
• 2-Axis Control
• 90 - 240 VAC, 50/60 Hz, Single Phase

• Power Input: 2300VA at 115 VAC, 4600VA at 230 VAC
• FP220 Front Panel

Configuration:
• AC Power Input: 90-120 VAC Single Phase, 50/60 Hz; 500 VA Max. at 7.9 amp Setting

• Motor Current: 0 - 7.9 amps, 0.1 amp Increments
• Fold Back: Automatic
• Bus Voltage: 160 VDC Nominal

This Danaher Motion / IDC H3411 Electric Cylinder Control Module is used and in excellent condition.

Input Power: 115 V
This Danaher Motion / IDC H155B-4-MF2-MT1 160V Electric Motor is used and in excellent condition.

H155B-4-MF2-MT1 Configuration:

• Motor Type: H = 160VDC, 2 Amp, Permanent Magnet
• Drive Ratio: 15 = 1.5:1 Drive Belt/Pulley
• Screw Pitch, Type: 5B = 5 Pitch (0.2 in [5.08 mm] Lead) Ballscrew
• Stroke Length: 4 = 4 in. (101.6 mm)
• Mounting Style: MF2 = Rear Rectangular Flange
• Rod Ends: MT1 = Male Thread
• Options: None


This Danaher Motion / IDC NH155B-4-MF1-MT1 160V Electric Motor is used and in excellent condition.

NH155B-4-MF1-MT1 Configuration:
• Rod-Type Cylinder: N

• Motor Type: H = 160VDC, 2 Amp, Permanent Magnet
• Drive Ratio: 15 = 1.5:1 Drive Belt/Pulley
• Screw Pitch, Type: 5B = 5 Pitch (0.2 in [5.08 mm] Lead) Ballscrew
• Stroke Length: 4 = 4 in (101.6 mm)
• Mounting Style: MF1 = Front Rectangular Flange
• Rod Ends: MT1 = Male Thread
• Options: None

Part Number: 930617

This Danaher Motion / IDC NH155B-4-MF2-MT1 160V Electric Motor is used and in excellent condition.

NH155B-4-MF2-MT1 Configuration:
• Rod-Type Cylinder: N

• Motor Type: H = 160VDC, 2 Amp, Permanent Magnet
• Drive Ratio: 15 = 1.5:1 Drive Belt/Pulley
• Screw Pitch, Type: 5B = 5 Pitch (0.2 in [5.08 mm] Lead) Ballscrew
• Stroke Length: 4 = 4 in (101.6 mm)
• Mounting Style: MF2 = Rear Rectangular Flange
• Rod Ends: MT1 = Male Thread
• Options: None

Part Number: 930825

This Industrial PCA-4943 is the Danaher Motion / IDC SmartStep-IPEC Microstepping Drive Control Board.

Part Number: PCS-4944
This Industrial Devices PCS-4946 is the Danaher Motion / IDC SmartStep-IPEC Microstepping Drive Power Supply Board.

Part Number: PCA-4947
This Danaher Motion / IDC NH155B-4-MF2-MT1-B1M 160V Electric Motor is used and in excellent condition. This unit does not include the end cap.

NH155B-4-MF2-MT1-B1M
Configuration:
• Rod-Type Cylinder: N
• Motor Type: H = 160VDC, 2 Amp, Permanent Magnet
• Drive Ratio: 15 = 1.5:1 Drive Belt/Pulley
• Screw Pitch, Type: 5B = 5 Pitch (0.2 in [5.08 mm] Lead) Ballscrew
• Stroke Length: 4 = 4 in (101.6 mm)
• Mounting Style: MF2 = Rear Rectangular Flange
• Rod Ends: MT1 = Male Thread
• Options: B1M = 1 Break on Motor

View Photo of missing end cap.

Part Number: 930812

28 / 28 Results
Contact Us
Fax:

(240) 376-1381