Parker / Compumotor S6 Microstepping System
This Parker Compumotor S6 Microstepping System is new from surplus stock. This unit ships in the original manufacturer's box, with standard accessories. The S series instruments are advanced step and direction input drives. The S6 Drive can be configured by on-board switches to be any of the following models:
S57-51, S57-83, S57-102, S83-62, S83-93, S83-135
If you would like an ATG technician to set the switches to configure the S6 to one of these particular models, please let us know when placing the order.
Input Voltage: 120 V
S57-51, S57-83, S57-102, S83-62, S83-93, S83-135
If you would like an ATG technician to set the switches to configure the S6 to one of these particular models, please let us know when placing the order.
Input Voltage: 120 V
Read Full Description
Stock # 58510-7
Description:
This Parker Compumotor S6 Microstepping System is new from surplus stock. This unit ships in the original manufacturer's box, with standard accessories. The S series instruments are advanced step and direction input drives. The S6 Drive can be configured by on-board switches to be any of the following models:S57-51, S57-83, S57-102, S83-62, S83-93, S83-135
If you would like an ATG technician to set the switches to configure the S6 to one of these particular models, please let us know when placing the order.
Input Voltage: 120 V
View Description
More Information
Overview
Datasheets / Manuals
View Live
Parker / Compumotor S / SX / SXF Series Packaged Microstepping Systems
Features
- Torques from 65 to 1,900 oz-in
- Speeds to 50 rps (3,000 rpm) Continuous
- 16 User Selectable Motor Resolutions to 50,800 Steps/re
- ...
- Three-State Current Control for Reduced Motor Heating
- User-Selectable Current Waveform for Smooth Operation
- Zero Phase Input Resets Phase Currents to the Power Up Positions
- Fault Output for Remote Signaling and Diagnostics
- Optically Isolated Step and Direction, Shutdown and Zero Phase Inputs
- Anti-Resonance Eliminates Mid-Range Instability
Description
The Parker/Compumotor S Family of drives and drive/indexer systems are designed for reliability and offer top quality performance. The S Series is a step and direction input drive, the SX Series is... a drive/indexer, and the SXF is a drive/indexer with encoder following. These products perform registration moves and are equipped to provide complex move profiling. The SX and SXF utilize the latest X-language enhancements and are easily programmed over an RS-232C interface. Common features of these drives and drive/indexer systems include the following:
• Torques from 65 to 1,900 oz-in
• Speeds to 50 rps (3,000 rpm) continuous
• 16 user selectable motor resolutions to 50,800 steps/rev
• Three-state current control for reduced motor heating
• User-selectable current waveform for smooth operation
• Zero phase input resets phase currents to the power up positions
• Fault output for remote signalling and diagnostics
• Optically isolated step and direction, shutdown and zero phase inputs
• Anti-resonance eliminates mid-range instability
• Fully short circuit protected—phase-to-phase and phase-to-ground with no time limit
• Enclosed to prevent contaminants from entering the drive enclosure
• Power dump circuitry protects the drive from large inertial loads
• RP240 remote panel interface
• Nine motors with 10 foot motor cables. Available in 23, 34 and 42 frame sizes
• Drive status indicators; power, step input, under-voltage, over-voltage and motor fault
In addition to these common features, the SX Series has the following:
• Extended edition of X programming language
• Motion calculation delay times as low as 500 microseconds
• Conditional branching commands
• Separate acceleration and deceleration commands
• 50 user defined variables
• Registration input
The SXF Series includes the common features, all the SX features, and the following:
• Encoder following controls speed and position of a slave axis based on speed and position of master axis encoder
• Synchronizes speed and position based on registration marks
• Change ratios “on the fly,” complex motion profiling
The Parker/Compumotor S Family of drives and drive/indexer systems are designed for reliability and offer top quality performance. The S Series is a step and direction input drive, the SX Series is a drive/indexer, and the SXF is a drive/indexer with encoder following. These products perform registration moves and are equipped to provide complex move profiling. The SX and SXF utilize the latest X-language enhancements and are easily programmed over an RS-232C interface.
Common features of these drives and drive/indexer systems include the following:
• Torques from 65 to 1,900 oz-in
• Speeds to 50 rps (3,000 rpm) continuous
• 16 user selectable motor resolutions to 50,800 steps/rev
• Three-state current control for reduced motor heating
• User-selectable current waveform for smooth operation
• Zero phase input resets phase currents to the power up positions
• Fault output for remote signalling and diagnostics
• Optically isolated step and direction, shutdown and zero phase inputs
• Anti-resonance eliminates mid-range instability
• Fully short circuit protected—phase-to-phase and phase-to-ground with no time limit
• Enclosed to prevent contaminants from entering the drive enclosure
• Power dump circuitry protects the drive from large inertial loads
• RP240 remote panel interface
• Nine motors with 10 foot motor cables. Available in 23, 34 and 42 frame sizes
• Drive status indicators; power, step input, under-voltage, over-voltage and motor fault
In addition to these common features, the SX Series has the following:
• Extended edition of X programming language
• Motion calculation delay times as low as 500 microseconds
• Conditional branching commands
• Separate acceleration and deceleration commands
• 50 user defined variables
• Registration input
The SXF Series includes the common features, all the SX features, and the following:
• Encoder following controls speed and position of a slave axis based on speed and position of master axis encoder
• Synchronizes speed and position based on registration marks
• Change ratios “on the fly,” complex motion profiling
The Parker/Compumotor S Family of drives and drive/indexer systems are designed for reliability and offer top quality performance. The S Series is a step and direction input drive, the SX Series is a drive/indexer, and the SXF is a drive/indexer with encoder following. These products perform registration moves and are equipped to provide complex move profiling. The SX and SXF utilize the latest X-language enhancements and are easily programmed over an RS-232C interface.
Common features of these drives and drive/indexer systems include the following:
• Torques from 65 to 1,900 oz-in
• Speeds to 50 rps (3,000 rpm) continuous
• 16 user selectable motor resolutions to 50,800 steps/rev
• Three-state current control for reduced motor heating
• User-selectable current waveform for smooth operation
• Zero phase input resets phase currents to the power up positions
• Fault output for remote signalling and diagnostics
• Optically isolated step and direction, shutdown and zero phase inputs
• Anti-resonance eliminates mid-range instability
• Fully short circuit protected—phase-to-phase and phase-to-ground with no time limit
• Enclosed to prevent contaminants from entering the drive enclosure
• Power dump circuitry protects the drive from large inertial loads
• RP240 remote panel interface
• Nine motors with 10 foot motor cables. Available in 23, 34 and 42 frame sizes
• Drive status indicators; power, step input, under-voltage, over-voltage and motor fault
In addition to these common features, the SX Series has the following:
• Extended edition of X programming language
• Motion calculation delay times as low as 500 microseconds
• Conditional branching commands
• Separate acceleration and deceleration commands
• 50 user defined variables
• Registration input
The SXF Series includes the common features, all the SX features, and the following:
• Encoder following controls speed and position of a slave axis based on speed and position of master axis encoder
• Synchronizes speed and position based on registration marks
• Change ratios “on the fly,” complex motion profiling
Read Full Description
Technical Specifications
Manuals, Datasheets, Drivers, Links
View It Live Request
Buying used equipment doesn't always have to be a shot in the dark. We know there are plenty of differences when it comes to used equipment and quite often, choosing between different pieces is difficult, especially when the equipment is not sitting right in front of you.
Well, what if you were able to see a piece of equipment before you purchased it? Not just a picture from the manufacturer's website, but the actual piece of equipment you would receive.
With InstraView™, we move you one step closer to inspecting the equipment you're interested in without having to wait for the equipment to show up at your door.
InstraView™ works in your web browser and allows you to view the actual piece of equipment you're interested in before purchasing. You can zoom in close to see the labels with the serial number or zoom out to see the overall condition of the equipment.
It's like having the store come to you!
InstraView Request Form
To get started...
1. Fill in the request form below
2. We'll send you an email letting you know exactly when your piece of equipment will be available for viewing
Item to Inspect: 58510-7 - Parker / Compumotor S6 Microstepping System
Related Equipment
- Stock# 58510-25
- Parker / Compumotor S3 Microstepping System
- Stock# 58510-5
- Parker / Compumotor S6 Microstepping System
- Stock# 58510-10
- Parker / Compumotor SX6 Microstepping System
- Stock# 58510-11
- Parker / Compumotor SX6 Microstepping System
- Stock# 58510-12
- Parker / Compumotor SXF6 Microstepping System w/ Following Option
- Stock# 58510-15
- Parker / Compumotor S8 High Current Option Microstepping System